GCE23LHWAFWW General Electric Refrigerator - Instructions

Tube was too short so I used the union to attach additional tubing to reach the valve at the lower rear of refrigerator

Replacing the water filter with the new style water filter was no problem...twist to the left, drop the old filter, line up arrows on housing and new filter, twist to the right and done.

Ice maker was always crusing ice. There is a spring deflector wound around the actuating rod towards the back of the ice dispenser. Pulled the ice dispenser out, slid the damaged spring off, and slid the new spring deflector on making sure to engage the actuator rod to restore it's action. Easy fix.

replaced with new connector and it worked great. also replaced the water filter and that was super easy!

It was a simple remove and replace. The new part fits directly in place of the old part. Its a pain to remove the light but once you get the light out the job is simple. The light must be pried out gently. It is snapped in place toward the air inlet cover and needs to be pried loose. Once the light is out there are 4 screws holding the air inlet cover in place. Remove the 4 screws and unfasten the wiring harness. Once the screws and wiring harness are disconnected remove the old part. Reinstall the new part in reverse order.

Emptied the door bin, removed it from its slots, and gently spread the plastic bin sides allowing the broken face panel to fall out. Replaced one end in the notches, gently widened the opening at the other end to slide the new face panel in, and jiggled just a little to seat the panel fully. Done!

1. Slide out refrigerator away from wall.
2. Unplug refrigerator electrical cord.
3. Slide out refrigerator further to be able to get in back of.
4.Turn off water control going to refrigerator.
5. Clear top shelf around water filter area, remove water filter.
6. Remove water filter cover housing lid by lifting off.
7. Using a ¼" nut driver, remove two screws attaching water filter housing.
8. Go to back side of refrigerator, & remove 2 screws from the silver cover plate of MWD manifold water line unit.
9.Using ¼" nut driver, remove lower cardboard cover that protects the motor & fan area.
10. Clean motor & fan area with old tooth brush gently, & vacuum dust off.
11.Using (2) ½" open end wrenches, loosen & remove both water lines.
12. Go to front inside of refrigerator. Gently pull out old water line manifold assembly, you may have to twist it some to get the protective sleeve out of the hole.
13.Insert new water line manifold assembly into the hole, when it gets to mostly in, gently work the protective sleeve through the hole.
14.Position the new manifold water filter housing into place & reinstall 2 screws. Do not over tighten.
15. Go to back side of refrigerator, gently push down on protective sleeve so you then can replace silver cover with 2 screws. Do not over tighten.
16. Remove old tape that was originally holding water line tubings.
17.Connect water lines to water supply lines, using (2) ½ " wrenches. Tight, but not over tight.
18. Re tape water lines to back of refrigerator, using a strong tape like duct tape in an orderly fashion.
19. Turn on water supply, check for leaks.
20.Re install black cardboard piece on lower end of refrigerator.
21. Plug in refrigerator.
22. Install water filter inside of refrigerator. Install cover over filter housing.

Pulled new tubing to the tank and put a union about 8 inches down from tank to new tubing. Great repair. Parts not readily available locally.

Watched a parts.com video on how to change defrost thermostat and followed the instructions

I removed the outer plate by sticking a very small screwdriver in the small holes at the bottom of the plate and pulling the plate toward me.
I then removed the 4 screws from the internal plate and pulled the plate toward me.
Then I romoved the 3 screws holding the old solenoid and unplugged it.
Next I put the new solenoid in place and replaced the three screws.
Finally I plugged in the solenoid and replaced the internal and external plates.

Removed front panel (using small screw driver) by popping it out, disconnected wire from solenoid, removed solenoid which was rusted, 3 small philip head screws held it in place insereted new solenoid,connected wire snapped front panel back in. Clapper valve closes tightly and no frost in frezzer, saved my self a bunch of money.

I bought a Flapper replacement part from Parts Select. I installed it following their very complete on-line video directions. Their complete and easy to follow directions made my job very easy, and the work was completed without any problems and just as good as if it were done by a professional repair person. I am proud of my work, it couldn't have been done without their video insructions. Also I got delivery of the part within two days of my order. I will alway look for Parts Select any time I need an applicance repaired. Thanks to Parts Select!

Procedure for Replacing the Ice Chute Plate
1. Turn off the power.
2. Snap off the outside trim ring. Use a plastic screwdriver to avoid scratching the cabinet.
3. Locate the three small holes below the control panel facing, just above ice chute. The center hole is not used. With a small, blunt, object (wire – blunted nail) that is slightly smaller than the holes, push up rather firmly up through the outer holes to release front control panel.
4. Remove the three wire connectors from printed circuit board. Firmly pull/pry them straight out of retaining clip. Use caution: Excessive force will break clips.
5. Release the secondary panel by removing four screws (one in each corner).
6. Remove the flap assembly.
7. Clean all accessible areas with 1/10 bleach water to sanitize. Rinse the cleaned area with clear water and thoroughly dry everything before re-assembling the panel.
8. Install the new flap assembly.
9. Re-installed everything in the reverse order and check the functionality.
10. Order a spare ice chute flapper to be ready for the next event.

To take the ice dispenser apart is not difficult. A ring removal tool would have helped to remove the auger. The Auger nut was difficult to remove and I used a visegrip to pull it off. Once the retaining ring was removed the repair was easy.
Never did it before but figured it out.

several times I had to remove the ice maker door solenoid due to it sticking. I ordered a new one from parts select. Problem solved!!!

Our daughter spilled juice on the refrigerator light button. It started with the light coming on very slowly and then not at all. We popped off the old button with a flat head screwdriver, plugged in the new one. Works perfect. Can't believe how inexpensive and easy the fix was.