GC2327PEDB Maytag Refrigerator - Instructions

Very easy to order from parts select. Took seconds to replace.

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!

Removed the inner door panel held on by 30 small nuts crews. Removed the old seal. Stretched new door seal onto inner door panel. Attached inner door panel and seal to inside of refrigerator door. Using a magnetic nut driver was the answer in the tight spots and the small nut screws. Everything works fine and the beer is cold again!

Replace the refrigerator lightbulb while traveling 88 mph then turned on the flux capacitor being carful not to get stuck in a worm hole. This allows you to fix the problem before it starts to go bad.

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

This replacement glass shelf arrived the very next day-after it was shipped. I was so impressed with the easy method of ordering and the prompt delivery of this product-also, the quality of the shelf was perfect. Great service!! I would recommend this for everything-as far as parts needed for repair or replacement.

At first I thought I had ordered the wrong bracket but all I had to do was push it up and pull down and it snapped right in place. If a 71 year old lady can do this any body can do it. Thank you for the fast service.

After taking advice from the other posts, I removed all contents from the door, removed the screws from the top hinge and then lifted the door off the bottom hinge pin.

While door was lying flat I unscrewed the old natural closer, replaced it with the new one. Swapped out the old lower hinge pin with the new one.

I then had someone help me lift the door back on the hinge pin and fastened the top hinge screws while they held the door in place.

It worked perfectly and was very easy.

I removed the top refrigerator side hinge screws. The door came right off. Slipped in the lower hinge pin.. Unscrewed the natural door closer and replaced. Reinstalled the door. It is unfortunate that these parts are plastic. They wear out way too soon. No, the door is not over weighted. If you have no weight in the door the plastic shelves will hinder the door closing. Putting stuff on the shelves makes them take their proper form.

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

Very simple fix, remove 3 screws, two connectors to the old switch

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!