GC2228EEDW Maytag Refrigerator - Instructions

Pulled broken plastic end stop from door. Basket fits right into the two side holes and pulls down to lock. Relatively easy fix and replacing basket stop.

First I removed the three screws in the top hinge that hold the upper right corner of the door to the body of the unit. Then I just lifted the door off of the refrigerator. I proped the door up just long enough to pull out the old pin (plastic) and put the new one in place. Next I picked up the door and set it on the new hinge, and last I put the three screws back into place. It has taken me about as long to type this out as it did to actually make the repair. The part was also very reasonably priced so I purchased two since this items has been replaced previously.

Nothing to it. I unpackaged the item. Cleaned it and placed in refrigerator. Great!

Dealing with your company was a breeze. From start to finish. Thank you for the transation from start to finish.

simple removal of old part by lifting and pulling, Reverse to put in new part. Not really even classified as "repair"

Ordered the parts, snapped them into place on the basket and then slid the arms into the holes on the freezer door, very very simple..

Cleaned out the door. Loosened the top hinge. Lifted the door off hinge pins. Replaced lower hinge, hinge pin and closer. Put door back on. Tightened upper hinge back down on door. Done. Very easy and door is not that heavy.

just snapped the new one in. I am very happy. the part was delivered in just a few days--I was surprised how quickly it was delivered. thank you. I would use your company again.

installed new parts

The best part of the repair was how easy it was to find and order the part. Instead of searching the parts houses around town I just went to the PartSelect web site, quickly found and ordered the part in about five minutes, received the part the next day at my home and was ready to make the repair. Wow! What a pleasure for something to work the way it was meant to. Removed old switch located by prying out with sharp knife or screwdriver. Don't worry about breaking it or cracking plastic. Disconnect(unplug) wires from back of switch. Replace (plug-in) wires on back of new switch. Insert in location of old switch. Finisheed.

removed old shelf.... cleaned where old shelf was.... installed new shelf.. job completed in 5 minutes

The most time-consuming part was removing the screws. First, remove the 8 screws that attaches the ice bin to the front cover. This will free up the auger enough to pull up the back end where the drive ring is held in place. The ring just pops right out. The only thing I recommend is as long as you have the bin out (and empty), go ahead and give it a good wash. Make sure it is thoroughly dry so that no ice freezes to the moving parts.

have always done it myself, but Maytag store closed, so I didn't know where to purchase filter

I received it from Parts Select, in 2 days and if I remember right, price was cheaper than I paid last year, at store.

Took out lower shelf. Unscrewed screws holding two broken shelf supports and removed broken supports. Replaced with new supports and screwed in the screws. Nothing to it.

Good news/Bad news story. One of your parts view showed the side rails without the drawer rollers another showed the rails with rollers. I ordered the rails expecting that they would come with the rollers attached. They did not so I had to place a second order for two rollers and two screws. As I live in CA, delivery was just a day for first order, but for second I ordered on Sat, delivery was on Tuesday. My complaint was double shipping and handling so total was almost $50.for two very simple items.

First, I removed the water/ice fountain panel - remove the 4 screws and disconnect the panel buttons cable. Second, I removed the panel circuit board - remove the two screws and disconnect the two wire connectors. Third, I pulled the water/ice fountain compartment. Removed the broken rubber pad (actuator pad), and installed the new one -- no tools needed for this step. Finally, I put everything back together. TIP: If the water/ice switch gets stuck, even with the new actuator, find a spring that can fit the switch pin that comes with the actuator. I had that problem, and I simply added a small spring.)