GC2227EED1 Maytag Refrigerator - Instructions

I read what other people had done so I tried the easiest solution--Forced, without breaking, the plastic & fit the ring right where it needed to be.

The most time-consuming part was removing the screws. First, remove the 8 screws that attaches the ice bin to the front cover. This will free up the auger enough to pull up the back end where the drive ring is held in place. The ring just pops right out. The only thing I recommend is as long as you have the bin out (and empty), go ahead and give it a good wash. Make sure it is thoroughly dry so that no ice freezes to the moving parts.

Pried out ice blade bar and removed broken water fill cup and replaced with new one.The whole repair costs $9.52 So I saved $ 190 over the cost of Appliance man visit!
It would have been $150& $50 for visit to replace ice maker unit.

Removed the top hinge of the door. Lift door off the lower hinge. Unscrewed the "natural closer" from the bottom of the door and replaced with new part. Pulled off the lower hinge from the lower bracket and replaced with new hinge pin. Replaced and realigned door. Piece of cake!

I simply removed the old brackets and replaced with the new ones. Can't get any easier than that!

Most of the time was sent to removing and replacing door shelves. Pry off upper hinge cover. Easy, it's only plastic. Remove 3 fastener from top hinge and remove hinge. Lift door off lower hinge. Lay door down on table let handle hang over edge. Remove door closer attach fastener. Remove and replace door closer. Pry lower hinge up and out. Tap new lower hing pin into place. Replace door, upper hinge and hinge cover. Had to replace Door Closer and Hing Pin together; both were worn and needed replacing.

Removed the food out of the fresh food door. Removed the top hinge cover, removed the 3 nut screws on top. Lifted the door off of the bottom pin. Set the door to one side. Removed the lower hinge pin with a screw driver and replaced with new product. Lifted door back onto lower hinge pin, secured the top pin hinge with the 3 nut screws, replaced the top hinge cover and placed food back into the door. Done in less than 15 minutes.

My husband did the replacement of the filter, so it was really easy for me. Easy for him too! The best part was this company had the best price, and the part was here in no time!

This was easy. Removed the plastic cover at the top hinge. Removed the 3 screws at the top hinge. Lifted the door off of the bottom hinge and laid it on it's side. The part that was worn out is the "natural door closer". It looks like this part will need to be replaced every few years, it is made of plastic and was ground down to nubs. Remove the screws holding it down and replace it with the new one. Lubed it up with some WD40 to get rid of squeaks. I also replaced the lower hinge pin, but I don't think that was necessary.

I used a knife blade to slip under the edge of old switch to pray it out of the hole it was inserted into, switched the wires and replaced the new switch into the same hole. It took about five minutes!

Poped ou the old switch, connected new switch and pushed back into socket.

Repair requires the removal of the bottom hinges on the doors. No problem for the refrigerator side, but the freezer side has wiring in the freezer door for the water/ice dispenser, so have some wood blocks handy to prop it up. Biggest challenge is that in the center of the kickplate there is a mounting screw (Torx head) that is behind the kickplate and runs vertically. I removed the old kickplate without removing this screw, just broke the kickplate off. The screw is very difficult to access with any tool. Removal wasn't too terrible because the old kickplate was gone; but insertion with the new kickplate in place was a challenge. I used a Torx socket, but because there isn't enough clearance for the ratchet, I held the socket into place by wedging a large flat blade screwdriver between the bottom of the socket and the floor. I was just able to get my index finger under the new kickplate to slowly turn the socket to fasten the screw. Unfortunately I didn't feel as though I could skip the screw - without it the kickplate sags in the center.

replaced electric control board, defrost for six hours. next day (24 hours) same problem, dusterhoff2928@charter.net

Used screw driver to pop out old switch. Used pliers to hold wire connection from fall back into slot on fridge. Inserted new swith into plug and pressed new switch back in place.

Removed old filter with a twist and installed new filter the same way. Very simple task.