GBD307PRB03 Whirlpool Wall Oven - Instructions

After reading all the other entries, I decided that I could do this! My first hurdle was getting the oven door off the hinges. Mine were not like any of the others described. My son-in-law looked at them and couldn't figure them out. So, I found the original installation instructions and, lo and behold, they said to flip the lever (one finger operation) in each of the rectangular holes holding the door onto the oven and then lift up until the door comes off. I did it, and it did! Boy, is it heavy! From there I just followed everyone else's instruction about undoing the screws, washing the glass panels, lining up the screw holes to get it back together, etc. One thing that took me longer was that the steel panel needs to go back the way it came out, not flipped! When I washed the glass panel it held, I put it down wrong and then "installed" it backwards. Luckily, I have a double oven and looked at the other one to see what was holding up the re-assembly! I'm glad that one of the others mentioned that the glass on the "bottom", the one that broke, isn't held in my screws or steel plates -- nothing, so I wasn't surprised when I got to it and it was "floating" on the insulation. My white insulation was like a fine fiberglass and was easy to stuff back in around the rim of the new glass. Took me a little over one hour. So, no more wet rags on hot glass (you'd think after living 72 years that I would remember this!) The glass fit perfectly and my husband would have been proud of me -- that I tackled a job that he usually handled, and that I saved over $200 for a couple of hours of labor and travel time.

Unplugged old element unit and plugged in new element. Took two needle nose pliers and a flexible body. Took about 5 minutes. Works fine. Anybody can do it. Make sure power is off at the box.

Opened overn door and inserted allen wrenchs through the holes in the door hinges. Close the door until it makes contact with the allen wrenchs, then grasp the oven door handle and the bottom of the oven door and lift up to remove the door. Place the door on a flat surface,(I used a bed) and remove the screws to gain access to the glass. Upon re-assesbly, leave door flat line up and re-install all screws before putting the front pannel back on. Insert door back into the oven and open, remove the allen wrenches and close the door. The process is easy and will take 30 minutes to an hour and save you a $100.00 service call!

Cordless drill removed 2 screws replaced element and 2 screws
Done. Didn't use new bracket

EASY. FOLLOWED THE YOUTUBE INSTRUCTIONS ON THE WEBSITE.

Easily, Removed the oven with help of my grandson, this model is quite heavy. Open the back cover panel, removed the old blower. replaced with the new blower, covered with the back protective panel. About one hour because some screws much harder to reach.

The tech said he used No 2 Phillip's. Once I took the door off and removed the racks I quickly learned a Phillips was not going to work. I am now the proud owner of a Kobslt star and square ratchet screwdriver.

Removed locking device

I looked up the problem and determined I needed to replace the limit switch which is inside the back panel. As a 78 year old woman who isn't afraid to tackle these problems I found this easier than most. Just be sure to disconnect the electrical connection if you don't have long enough length to pull oven from the wall cabinet. I won't put any sheet pans in the oven next time I self clean it.

1) Removed the trim pieces (2 screws). 2) removed the 2 screws holding the oven in the wall. 3) Slid the oven out of the wall cabinet 4) removed the back panel of the oven ( 10 screws. 5.) removed the old thermostat (2 nuts) 6.). Installed the new thermostat and reversed steps 4-1

Since there is multiple glass panels with several brackets, screws and insulation within the oven door I strongly suggest to take photos at each step using your smart phone. Do not attempt to remove all the components at once. Bracket positions, screw locations and glass orientation is necessary. This is the best advice I have to make this a quick and very easy job.

I turn off the power in the breaker box and then unscrew the part and replace it with the new one

unscrewed the oven door, took off the entire door, pulled apart the glass pieces and replaced

removed door from oven, took all screws off door to remove glass, put new glass in place, put oven door back together, put oven door back onto the oven

First we watched a YouTube on how to replace the thermostat. It was easy to turn off the circuit breaker. It was a little tricky to pull the range away from the wall and then we were able to unplug. Because our range is a dual fuel model, the back had a lot more screws to remove to get to the thermostat because there were covers over a lot of wires and the gas line I presume. However, we did get off the 12 or so screws with a regular screw driver. We easily located the thermostat and quickly realized that the two screws holding the thermostat in place were neither flat head nor phillips. We were able to remove one of them and merely twisted it sideways, installed the new thermostat with one screw and attached the wires. When we flipped the circuit breaker and plugged in the over, Voila, it worked. The hardest part was getting all the covers off the back. I hope it doesn't happen again because this was an expensive replacement part.