FWT445GCS0 Frigidaire Washer - Instructions

I had called a repair man; and fortunately he never returned my call. After reading many of the reviews involved with the same problem, and wanting to use my washer, I decided it was easy enough to give it a try. And so it was. 2 screws in back removed the cover; and 2 screws in the front of the washer permitted the removal of the affected part. Removed three "plugs" from old; put them on the new part; replaced it back in the washer, and replaced the two front screws, which held it in place. Replaced top, securing with the two screws. And surprise - surprise -- the washing machine was working again! Your reviews were so helpful and encouraging --- that this really old lady decided to try it --- and like they all said "It was really easy to fix."

I found and ordered a new latch from Partselect.com. After a few days I received the new part. I used a square drive screwdriver to remove the two screws that retained the broken latch, put the new latch in place, and reinserted the retaining screws. The job couldn't have been easier.
I couldn't be happier with the quality of the part or the speed of delivery and wouldn't hesitate to order from Partselect.com again.

I removed the 2 screws holding the broken door catch in place, and attached the new door catch with them. The repair could not have been easier, and now the door works great.

Also, I ordered the part, and it arrived via FedEx the next day. That greatly exceeded my expectations!

I removed 2 screws from the the top back of top. Removed the cover. Removed the 2 screws holding the door lock assembly.Removed the door lock assembly, disconnected the 3 wiring harnesses. Connected the wiring harnesses to the new door lock switch assembly. Installed the new unit in the door lock, reinstalled the top.Done.

2 screws out then 2 screws in.

Once I opened the knob by rotating the old one counter-clockwise, changing is as simple as screwing the new one in.

I was having issues with the door catch. It looked worn, so I ordered the $10 (plus $13 shipping) part. Replaced the part, same issues. Figured out the hard plastic door catch was just not designed large enough to keep the door (a.k.a. lid) closed. My brilliant brother suggested I just put a piece of masking tape on the tip of the door catch to enlarge it. Guess what? It resolved the problem. I could have saved $23 and used masking tape that was left in the garage by the previous owner of my house.

First, I unplugged the washer then removed the front panel to the washing machine, then the pump cover, then the two hoses connected to the pump, draining them into a small bowl. I removed the ground wire and electrical connections.

Then I removed the two bolts holding down the pump and removed it. I had to pivot the hose connections on the pump to match the old one. Once I did this, I removed the hold-down bracket from the old pump and installed it on the replacement pump.

Getting the hoses clamped back on the new pump was a challenge, and I finally used an automotive clamp on the rear hose. Once the hoses were connected, I bolted the pump back in, reconnected the power and ground connections and replaced the cover.

Overall, it was a fairly straightforward installation and the only challenging part was the hose clamps.

no problemO top loader. open top, disco two electrical plugs and a small hose, then remove two screws that hold valve in place and remove. Re install in reverse order. Thanks for your support Eliot in Alaska!

No tools necessary. Simply turn old knob to the left or counter clockwise and it will disengage. Slip on the new part and turn to right or clockwise until it is tight. 2 minute project.

The door catch on the washer broke, and I had to epoxy the broken catch to finish my laundry. I looked for the part online, and PartSelect not only had the part but had a photo of it as well. I was very impressed with how quickly the part arrived, and within 15 minutes the repair was complete. Thanks for having the photos and getting the part to us so quickly.

simply grasped the remaining segment of the switch with the pilers and turned it counter clockwise and once removed threaded the new one on.

I followed the instalation instructions provided with new parts. Getting the mounting pins out was relatively easy However, the shock on the right, behind the pump, was a bit more difficult to remove than the one on the left. I took the rubber drain off the pump in order to get at the pin behind the pump. The new replacement shocks came with the plastic bushings inserted in the shocks in alternate directions. The original pins were all inserted into the bracket / shocks from the rear so when I installed the new shocks I reinserted one bushing on each shock so they we both oriented in the same direction. The instruction says to be sure the mounting pin is pressed from the side with the busing collar. It seemed strange the shocks came that way, with no mention of switching them. The most difficult part on the installation was pushing the pins back through the bracket and shock since there was no easy way to push the pins in from the rear. I used a large channel locks on the left side, but the right side was more difficult with all of the obstructions. I finally was able to push in place with my bare hands but was very difficult. Sorry to say the new shocks did not cure the vibration at all. I was very careful to make sure the machine is level. I'm not sure if there is a cure other than replacing the machine.

Watched the video on website and followed what they said. Worked great.

Removed the back and lower panel in the front of machine. Turned it on its side to replace spring, not tools required. Then stood it up and replaced both shocks by removing plastic pins that hold them in place, no tools required. The only time you need tools is to remove the metal panels to get to the parts. Now it makes no noise and runs like a new washer. Paid $140 for the parts, a new machine would have cost over a thousand and would be one of those digital nightmares that don't last as long. This machine is 18 years old.