The door strike on your washing machine allows your washer door to lock properly, and operate efficiently. If you notice that your washer door will not open or close, leaks or the washer will not star...
$19.58
In Stock
Order within the next 57 mins and your part ships today!
This kit is used for front load washers and includes 2 dual-stage shock absorbers, 1 spare shock mounting pin and 4 locking nuts. These shock absorbers keep the washer from vigorous shaking during it's cycles.
$50.58
In Stock
Order within the next 57 mins and your part ships today!
This door lock and switch assembly is manufactured to lock the door on your front load washer to prevent it from opening while it is running. You may need to replace the door lock and switch if the do...
$163.10
In Stock
Order within the next 57 mins and your part ships today!
The pump is what your washer uses to remove the water from the tub. This part is the pump and motor assembly which includes the red flapper to prevent drain back flow.
$211.11
In Stock
Order within the next 57 mins and your part ships today!
Also known as a Door Boot Seal and is used in front load washers. This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately f...
$393.85
In Stock
Order within the next 57 mins and your part ships today!
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
$16.47
In Stock
Order within the next 57 mins and your part ships today!
Order within the next 57 mins and your part ships today!
Questions And Answers for FTF2140FS1
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Kent
July 7, 2021
As soon as I turn on, it dumps water all over floor.
For model number FTF2140FS1
Hello Kent, Thank you for the question. This could be several issues. We suggest checking the hoses to make sure nothing has come loose. You can also check the Drain Pump for damage that is causing a leak. Depending on where the water is coming from, you can also check the Water Vale for a leak. Thank you for your inquiry, good luck with this repair!
Hi. The washing machine front board show no lights on. Power is ok. Any fuse or breaker inside or on the control board, please?
Thanks
For model number FTF2140FS1
Hi Sue, thank you for reaching out. Our research has found that it is most likely the Control Board, part number PS12724037, there is no fuse to replace on the control board. We hope this helps.
Washer will fill only on Soak cycle. What's wrong?
For model number FTF2140FS1
Hello Al, thank you for contacting us. According to our research, we would recommend checking the water inlet valve for any blockage. If this is not the issue, you may need to replace the control board, part number PS12724037, to fix the issue. Glad to be of assistance!
The problem with my machine was not listed and that is simply that the machine will agitate, fill and drain with water but will not spin. When the spin cycle starts there is just a buzzing noise which may suggest it's the clutch but unfortunately you did not address this symptom in your q&a section, can you please advise before i start dismantling the entire machine. Thank you.
For model number FTF2140FS1
Hi Hugh. Most commonly something is stuck in the pump and blocking it. Thank you for your question and good luck with your repair.
This washer was in a house when purchased. We are moving again, how do you remove all water for easy lifting.
For model number FTF2140FS1
Hi Doreen, thank you for your question. There should be no water inside of your machine if your machine is not in an cleaning cycle. You might want to check your drain hoses and drain pump to see if they are clogged and functioning. To remove any stuck water because it is not draining out, you may have to open up your machine and disconnect the hose to your drain pump to allow the water to flow out from your tub. You will need a bucket and towels to catch any excess water. Good luck with your repair.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
This was one of the simpliest repairs I have ever done taking less than 5 minutes to complete. On the inner door I removed the two screws that hold the plastic catch in place. I then removed the broken catch and put the new catch in place. Finally I replaced the two screws that hold the catch in place and it was done.
1. Unplug unit. 2. Unscrew 2 nuts holding top in place in rear of unit using phillips head screwdriver. 3.Slide top back and remove. 4. Open door of washer and unscrew 2 screws holding in door lock unit. 5.Pull out unit from the top and install new unit reconnecting the 3 wire connections.
remove top of machine by removing 3 screws along the top edge in the back of your machine and then sliding the top back and up. Then loosen the screws holding on the control panel enough to get to the 2 screws at the top of the door panel. Next remove bottom panel by removing 2 screws along bottom edge then pulling it free from snaps. Then along the outside lip of the bellow, just inside the door, is a wire clip that is easily removed by prying it past rubber lip with a screw driver and lifting it away. Remove the door panel by removing the 2 screws you exposed by loosening the control panel and 2 more along the bottom that were exposed when removing bottom panel. After the door panel is removed and the bellow is completely exposed, you will find that it is held in place by a circular spring which wraps the whole way around the drum opening. Again it can be removed by prying it out away from the groove in which it sits with a screw driver. Now your machine is broken down as far as it needs to be. From here you can follow the directions included in your new bellow kit and put it back together by following these instructions in reverse.
