FSG446RHS4 Frigidaire Dryer - Instructions

Previous comments on line were so helpful.

My husband and son took the dryer apart by removing the top in order to get to the drum. Part of silver rim that the Drum Glide is attached to was broken,it had been cut somehow. They had to soder it back in place so they could attach the Drum Glide and so far it's working.

Felt- I just ordered one with the adhesive and removed the damaged section used a wire brush, applied the adhesive ( which was more than enough) waited a few minutes for the adhesive to set, applied the felt, attached binder clips to hold it in place while working on the Drum Glide. Really easy.

The new rotary knob just popped right in. No problems. It was a perfect fit.

My wife was able to easily do the repair before I could get home from work to do it. She watched the PartSelect video on her iPad as she did the necessary steps to get the belt replaced. We only needed one glide replacement, as one was still attached and intact. We should have purchased both sets of felt seal replacements, though that wasn't as urgent.
My wife thought the repair was quite easy overall.

First of all, the folks at Part Select have been terrific. I balled up my address and they were great in correcting my error and getting the parts promptly to me. They provide directions with the parts. And You Tube, is a wealth of information too. The process is to remove the drum and replace the nylon busihing that supports the drum at the back of the machine. Getting it out was no sweat. Getting the drum back in was a bit more challenging single handed. If I was going to make any suggestion it would be this is a good project for two sets of hands with the second set needed for about ten minutes. The You Tube video I watched said putting the front cover with the drum attached to the back of the unit would be the challenge and they were right. Otherwise, super easy and the results are it's back to "new" condition. Thanks again to Part Select!

The new motor from parts select was not correct. The new motor is a bolt on. The original motor was a press on. Had to return at a cost of 42.00 dollars. Had to buy a new dryer.

1. unpluged the dryer and turned off the gas.
2. pulled dryer out so i'd have ample room to work on it.
3. used large flat blade screwdriver in the front between the top lid and dryer face to gently pop-up the lid.
4. removed 4 screws from inside, that hold the face to the main box leaving the wires all intact.
Found the coils on the lower left, held in place by two screws and plate.
5. took a good look at thier orientation before unpluging old and installing new, I recommend one at a time.
6. Vacuumm any exceess lint and check foam seal between lint trap and exhuast duc, the glue came undone on mine causing extra lint dust that is potentially flamable.
6. screw dryer front back on to main box, make sure to check wiring harness and that all electrical blade connectors are still pluged in to their componants.
7. At this point plug in, turn on gas and do a test run.
8.if everything checks out good then lower top make sure flexable exhuast hose is still connected on hte back of the dryer.
9. Tell your wife or girlfriend or husband or boy friend they can now finish your laundry :)

removed the top of dryer, pulled front panel back from drum and installed snubber(Front Drum guide).

after numerous holes put in my families clothes i looked on line and found "partselect.com". i ordered the front drum glide after seeing a similar story about the clothes being torn and getting caught and my family and i have our new dryer back!! yeah :<)

Thanks to Justin in Customer Service I was able to get the correct replacement knob. It arrived and I installed it in seconds flat. It works great and you'd never know it wasn't original.

Thanks.

Before this fix which worked beautifully, I tried replacing the flame sensor which did not work. To read that story, search under part number PS459818 (Flame Sensor). Our model is a Westinghouse, so access to the unit is a bit different than the other stories. It's a stacked front-loader sitting on top of a washing machine.

1. Open the little front door (lower left side) by unscrewing the little screw right below it. The door will pivot and slide out vertically.
2. Disconnect the electrical main lead coming from the back of the unit (just in case).
3. Close the gas switch lever on main gas pipe coming from the back on left side (just in case).
2. Remove 2 phillips screws on top of the metal bracket holding the two coils. The screws have to be removed completely along with the bracket. It's easy, they are right in front and there is room for the screwdriver. Use a thin long one instead of one with multiple bits to better align with the screws, which are very close to the coils.
3. The two coils slide right out and are very different so it's easy to keep them straight. Remove electrical connectors before or after removing the coils (I marked the plastic on top with a sharpie to keep them in the right orientation).
4. Drop in the two new coils and reconnect them to the electrical leads.
5. Reconnect main electrical lead from back (match wire colors)
6. Reopen gas lever on gas pipe.
7. Drop in front cover at an angle, tilt vertically and put screw back underneath. Use magnetized screwdriver or a piece of scotch tape to hold the screw or it might fall off the screwdriver.
8. Voila'. It worked.

This website is great. Our dryer is a Westinghouse bought in 1991 (almost 20 years old!) and with this fix it's just like new. In 1994 we used parts bought here to fix our washing machine (Westinghouse LT350RXW1). That machine is now 15 years old and still going!

Just pressed the knob on.

Just put on the new knob! Supper easy and it works great!

Simply popped it back into place, careful not to break the new handle.

Took it out of the bag and put it on.

I definitely would not have tried to do this had it not been for the other testimonials written here. But it sounded so easy, I had to just try it (the repair man estimated that with parts and labor, we would be looking at somewhere between $250 and $300!).

The repair itself took less than 15 min, but I spend a good deal of time looking around the garage for a few screwdrivers and my socket set (me and tools don't meet too often). I could simply pry up the top cover on the dryer with my hands, then got it all the way up after removing two screws from the lint trap and undoing this really annoying wire connector thing. From there the front panel lifted off. To remove the drum, just had to release the tensonier on the belt, and it came right out. From this point it was really obvious where the replacement parts would be going. A few screws later, and I could swap the parts, and put humpty dumpty back together again.

It works!!!