Models > FSE848RHS0 > Instructions

FSE848RHS0 Frigidaire Dryer - Instructions

All Instructions for the FSE848RHS0
121 - 135 of 587
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer stopped heating.
Called a repair co. Said it would be about a week before he came to the rural area my mom lives and he probably wouldn't have the part. He would order it after he determined the problem. So I went to your web site and ordered the item it said was 80% and two other parts just in case. He came and used the Heating Element Assembly and said it was a good thing we had it. He would have had to order it and come back probably a week later. THANK YOU!! WE needed the dryer repaired sooner and saved another service call. I am returning the other parts not used and you make it so easy to do. I plan on using your site again.
Parts Used:
Heating Element Assembly
  • Pam from Borden, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The thermostat had deteriorated and no heat
Had to loosen drum and move it forward to get at switch. Didn’t have to remove belt.
Parts Used:
High Limit Thermostat
  • David from ROUND TOP, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
lack of heat
Remove top lid by pushing tab on either side with a putty knife. Disconnect the 2 wire carriages on right. Remove one
phillips head screw on each side that holds front panel to dryer body. Remove front panel by using flat head screwdriver to pry panel from body. Remove thermostat located on bottom right attached to front of motor on a plastic body by removing two phillips head screws. Disconnect wires and place on new part.
Parts Used:
High Limit Thermostat
  • Ann from WALLA WALLA, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lint filter was wearing out.
Just replaced the new lint filter with the old lint filter. The part fit perfectly. I did not have a problem.
Parts Used:
Lint Filter
  • Barbara J. from Lancaster, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The D part of the Timer knob broke.
All I had to do was line the "D" shaft up with the "D" metal shaft on the Dryer and push the knob on. I made sure it would turn properly, and turned the Dryer on the make sure it worked. All is good.
Parts Used:
Timer Knob
  • Billie from EDGEMONT, SD
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No problem
Just snap into place
Parts Used:
Door Handle
  • Terrance from MENOMONIE, WI
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
was using a pliers to turn the part without the knob on and off; just didn't cut it; my family told me about your website and it was EASY!
just put it on in 5 seconds!
Parts Used:
Rotary Knob
  • Lisa from Los Angeles, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Knob
Took it out of the bag and put it on.
Parts Used:
Timer Knob
  • Sharron from Portland, OR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door handle broke and came off.
Simply popped it back into place, careful not to break the new handle.
Parts Used:
Door Handle
  • Elizabeth from Mentor, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Knob was cracked
Just put on the new knob! Supper easy and it works great!
Parts Used:
Timer Knob
  • Natalie from Logan, UT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Knob broke
First I used a pliers to remove the piece of the broken knob that was still attached to the shaft. Then I pushed the new knop onto the shaft until it snapped into place.
Parts Used:
Rotary Knob
  • Louis from Pasadena, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replaced broken timer knob
Just pressed the knob on.
Parts Used:
Timer Knob
  • Corey from Lodi, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken knob
It was very easy, looked and found the right match and pulled off the broken one and pushed on the new one
Parts Used:
Timer Knob
  • Lawrence from Milwaukee, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dryer wouldn't heat
remove top of dryer by prying with large screwdriver to snap back clips that hold it on remove two screws on both sides that hold the door . remove door then remove belt from dryer tub. (to remove belt take the back panel near floor off with screwdriver and lift pullie up that hold belt. )then lift tub upward to disconnect it from it's seat; pull it straight forward to get to the heating element.un bolt it with screwdriver and disconnect the sensor and put new heat element in
Parts Used:
Heating Element Assembly
  • billy from millsboro, DE
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Loud Squealing
Remove top panel with large flat screwdriver and 2 screws in back.Remove bottom panel with 2 screws.Release belt tensioner and remove belt.Remove 3 screws in center of drum inside.Remove drum. Remove rear bearing by pulling up on assembly.Replace all parts in reverse order.
Parts Used:
Rear Drum Bearing Kit
  • William from Hudson Falls, NY
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the FSE848RHS0
121 - 135 of 587
Back to Top