FRS20QRCD5 Frigidaire Refrigerator - Instructions

I talked to a human who spoke english and was pleasant. She managed to work with me in a timely fashion to order the desired piece of Kenmore refrigeration equipment in less time than what iiwas trying to do myself on the internet. Her knowledge that was very valuable made this experience exceptional and memorable. However, the price to replace a crisper drawer is ridiculous.

The front piece had to be removed by slipping it off the broken drawer and then slipped back onto the front of the new crisper drawer. The bottom did not exactly go where it was designed to go so there remains a gap. I could use tools or forcably try and pry it into place so it is flush and pretty but the thought of breaking it sends my wallet into seizures.

Very simple. I removed 2 screw each holding the old drawer support glide and I replaced it with the new support( 3 minutes to replace using old screws )
To replace the drawer I removed the front part of the drawer(just pop out) and I attached to the new drawer(no tools needed).
Now It looks I have a new refrigerator.

I slid the trim above the door handle up to remove it. Then I slid the trim below the door handle down to remove it. Once the trim was removed the entire door handle was exposed. I removed two screws, removed the broken door handle and installed the new door handle using the same two screws that I had removed. The trim does not slide back on very well. It is better to remove the plastic clips from the door and attach them to the trim first, then clip the trim back into the door.

I removed the drawer fronts from the old drawers and slid them onto the new drawers. My fridge is like new again and the repair was a lot less expensive than buying a new one. My drawers arrived the day after I ordered them!!

Put the new shelf into position-Voila!

For the shelf you have to save the front and back gaurds to put on the new shelf when it arrives. You have to slide the shelf in through the slots and then add the back gaurd. The front guard just pops on after that. The drawer front of the old drawer just slides off and then back on the new drawer, The drawer just slides in after that. No tools needed. Super easy ... super beautiful. Love it!

Found the part on this site ordered and received part in 3 days. Took approx. 10 min to replace. Thanks for the quick service.

Installed salvaged pan cover edge guards from broken pan cover. I installed new pan cover in grid.

Just took it out of the box, wash it and put it on the inside door.

We took the door off and replaced the pastic washer. Found out that the repair people never informed us that the door itself has a bit damaged so this repair would have to be done over and over. Nice way for them to make money off us.
We were able to fix it so that it will last a LONG time. Sometimes it realy can pay to do-it-yourself!

Unplugged fridge, opened the door, used flat head screwdriver to pop off old switch, unplugged wires, plugged in new switch, popped it back in, and plugged the fridge back in. 2 minute fix.

raised the sides of the drawer front up, then pulled the front straight up. Then put the front in the slots of the new drawer and pushed down. I gave it a light tap on the top corner and it locked into place. I put my food stuffs back in the drawers and slid them back into the refrigerator. Job done in about eight min, for two drawers.

A little research told me the hum plus no cooling was either the compressor or the relay. I ordered the new relay and put it in but it didn't fix the problem. I ended up having to buy a new fridge, but it was worth the $30 gamble to see if I could fix it on the cheap and it saved me the money a service call would've cost. Pretty easy installation, just in a tight space on my model.

Traced issue to defrost timer ( burned compressor & element contacts). This unit is mounted next to the temperature adjustment control in the refridgerator area - right in front. Removal of plastic cover provided easy access to the timer. Unit unscrews from the mounting then unplugs. Installation is reverse of removal.

First we removed the trim from door, then we took out the 4 screws that were holding handle on. We then took new handle & placed it on the door & added the 4 screws onto it. We replaced the trim and we were finished. This whole process took less the 10 minutes.