FPCE19TPL0 Frigidaire Refrigerator - Instructions

MIKA from WARFORDSBURG, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

light blub blew

unplug power from ref removed old light socket only difference wired a little different checked new socket compaired to old checked terminal ends small big looked at wires big,little plugged up put in new light blub plugged ref power back on work power off pushed socket bac in power on works

Parts Used:

Light Socket

earl a from GIRDLER, KY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

4 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Missing Freezer Door Shelf Bars

Snapped in missing brackets, cut bar to fit and installed.

Parts Used:

Door Shelf Bar - White - Cut to fit

Susan M from VIRGINIA BCH, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

End of door shelves broke & were held on by duct tape for a long time

Since the end caps were already broken I just took them out & put the new ones in. Total time to do this was less than 5 minutes. Great parts, great prices & super fast shipping

Parts Used:

Darcy from West Palm Beach, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Shelf on door broke

The plastic ends that held the shelf on broke off, once my new ends came in the mail I had to attach them to the metal bar that holds the condiments in the door's shelf. To do this I had to hammer the ends of the shelf a little to get the caps to fit. Once they were on I put the ends of the caps into the holes on the door and had to push down with some force to get them to snap in. Very easy once I realized I had to push harder than I expected to get them to snap in. It's great to have my shelf back!

Parts Used:

Jamie from Pierre, SD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

End caps broken - shelf kept falling off

Snapped the end caps onto the existing shelf, and eased the assembly into the door slots. Light tapping with a hammer was required to fully seat the assembly into the door. All in all, a straightforward and simple repair.

Parts Used:

Barbara from Gaylord, MI
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Defroster didn't work

Ordered a new defroster timer and replace old one. It works just fine. A $35 repair vs a $500 new appliance.
Cool.
GWE

Parts Used:

George from Eatonville, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

broken shelf clips

snapped in the one end, placed the bar in one end and the other clip on the other end and snapped it in place.

Parts Used:

Donald from Spencer, IA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Coils kept icing and refrigerator stopped cooling lower compartment.

Replaced defrost timer & thermostat.

Parts Used:

Defrost Thermostat

Raymond from Sierra Madre, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

5 of 14 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Refrigerator keeps frosting up and not cooling

Refrigerator started frosting up and running all the time.I'd defrost it and it would frost up again in about a week.The timer seems to be work so I just guest it mite be the Defrost Thermostat.I removed the duck in the center and back panel in the freezer compartment defrosted it and switched Thermostats and replaced panel and duck, going to lower compartment of the refrigerator.So far it seems to be working a little more time while tell.

Parts Used:

Defrost Thermostat

Marvin from Pima, AZ
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Crisper cover support Bar was broken

Put glass in the new crisper cover and the support bar in place.

Parts Used:

Crisper Pan Cover

Crisper Drawer Cover Support Bar

Patricia from Eupora, MS
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Refer iced up and would not keep the bottom cool. It was 70 Farenheit inside.

I simply removed 4 screws holding the casing and then 2 more holding the timer. It was very easy. I then replaced the timer by unplugging and plugged the new one in. I replaced all the screws and the job was done. Less than 30 minutes. I was very impressed with the shipping time. When I ordered the part, I had it the next day.

Parts Used:

Larry from Newton, KS
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

No freezing or cold in either freezer or refridgerator - compressor did not run.

Traced issue to defrost timer ( burned compressor & element contacts). This unit is mounted next to the temperature adjustment control in the refridgerator area - right in front. Removal of plastic cover provided easy access to the timer. Unit unscrews from the mounting then unplugs. Installation is reverse of removal.

Parts Used: