All Installation Instructions for Frigidaire Refrigerator FGUI2149LP3

It was broken in the front part that hooked in the hole

Took the drawer and shelf out then took the screw out and took the old one out and then put the new one on.

Parts Used:

Meat Drawer Rail - Left Side

Harriet from LOCKWOOD, NY
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Light Switch too loose so no longer triggered by the door.

Googled it on Youtube - unplugged the fridge, used a paint scraper to loosen the old light switch, unplugged it from the electrical source, connected the new switch, replaced the whole unit into the proper location and pushed it firmly into place.

Parts Used:

Light Switch

Linda from BOZEMAN, MT
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Light Switch not working properly

After unplugging the fridge, I took a small flat headed screwdriver and carefully pried off the light switch from the inside, right side of the refrigerator. I disconnected the 2 wires from the switch and replaced it with the new switch and pushed it back into the frame of the fridge. Done !! Very very easy !! Thank you

Parts Used:

Light Switch

William from ORMOND BEACH, FL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Old door seal was cracked and didn't seal tight.

Pulled off the old seal and put the new one on. No tools needed. It fit where it was supposed to and seals the door like new now! Thank you!

Parts Used:

Refrigerator Door Gasket

Rosemary from FRUITPORT, MI
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

torn and cracked gasket

Took off the old one, replace the new one in less than 5 minutes

Parts Used:

Refrigerator Door Gasket

janet from Parryville, PA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

plastic drawer slide was broken

First I watched the video that provided - extremely helpful - thank you- when the part arrived I removed the drawer and shelf - unscrewed the screw- pushed the slide catches to one side and removed - then I screwed new slide on - pushed to lock in the catches and DONE! That simple - EASY PEESEY!! THANKS SO MUCH FOR VIDEO AND SUPER FAST NEXT DAY SERVICE - AMAZING HOW FAST!! WILL USE ANYTIME I NEED PART AND HIGHLY RECOMMEND YOUR SITE! TIME- 5 MINUTES TOPS!

Parts Used:

Meat Drawer Rail - Left Side

Meat Drawer Rail - Right Side

brenda from hillsboro, MO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

door gasket torn on top

followed installation video on your website which was very helpful. Very easy repair. The packing material was great.

Parts Used:

Refrigerator Door Gasket

James from FORESTDALE, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Rail had split and would not support drawer.

Removed drawer. Removed shelve. Flipped shelve over. Removed one screw. Undid tab on each end. Removed bad rail. Replaced with new rail and reversed order. Easy fix.

Parts Used:

Meat Drawer Rail - Right Side

Douglas from HOUSTON, TX
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Gasket was oversize and compression spline would not stay in door groove

Required a trip to the hardware store. Online research showed that Gorilla Glue would hold gasket in place and was recommended for that task. Needed to glue each side separately to keep the spline in the groove. Took far longer than it should have!

Parts Used:

GASKET-Freezer DOOR

CECIL from PHOENIXVILLE, PA
Difficulty Level:
Difficult
Total Repair Time:
1- 2 hours

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Broken freezer door gin

Hah! It took 1 minute to open the package and 10 seconds to install. The shipping response was incredibly fast. Great Service!

Parts Used:

Freezer Door Bin

Dean from Nevada, IA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

One blade broke from condenser fan

The part i recieved, from parts select was a larger in circumfrence (<1/4) than the original. However i was not aware of this until after i treid to repair it.

I removed the broken fan from the condenser. This was very sipmle.

When i pluged the refridgerator back in to the outlet the fan tried to start up but soon began to make aloud noise, due to there not being enough clerance.

Parts Used:

Condenser Fan Blade

Chris from Lockport, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

11 of 30 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

old refrigerator door shelf broke

Installing the new shelf was easy.

Parts Used:

Refrigerator Door Shelf Bin

Rod from Rio Rancho, NM
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Ice maker not making Ice

Unscrewed (loosen) screws lifted unit out unplugged electrical connection. plugged in unit hung on screws tightened screws and had ice in less then 1 hour. Rick

Parts Used:

Refrigerator Ice Maker Assembly

Colline from PENDLETON, OR
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

You have sent the wrong part for the THIRD time. You have sent aaccess cover that is TWO INCHES too short. It does not cover the opening, and you will not answer your phones.

There is no way to complete the repair with the wrong part, You have had my order since June 22nd, 2020 and the incorrect part arrived October 27th, 2020. You charged $7.79 plus $1.06 tax and $9.95 shipping. Please refund the entire amount including the shipping, since I did not ask you to ship the incorrect amount.

Parts Used: