All Installation Instructions for Frigidaire Refrigerator FGUI1849LP2

The original part was plastic/and broke

unscrewed to little bolts and installed the new/metal part we got rfom partselect.If we may say.this is a great company to buy from! Fast!

Parts Used:

Upper Hinge

John from Lancaster, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The door shelf broke.

Very easily did the repair -- popped the new door shelf right in the place of the old one! No tools needed, no hardware, easy! The part actually measured 24 3/4 but the replacement part said "26 inches" on website & this was THE replacement part. Put this off for so long--ordered part and recd within 2 days, great!

Parts Used:

Refrigerator Door Shelf Bin

Lori from Catskill, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Repaired Oven Range Light Bulb

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

Parts Used:

Light Bulb

Alan from SAN MATEO, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Ice maker stopped working. Part needed to repair it no longer available so had to replace the whole icemaker.

Loosened the two mounting screws (no need to remove them), lift off the icemaker and unplug it. Reverse the order and done.

Parts Used:

Refrigerator Ice Maker Assembly

Edward from GROTON, CT
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

4 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Needed to replace shelf

I can't believe I put if off so long... so easy to do and PartSelect was very fast, efficient, and the cheapest vendor for my part.

Parts Used:

Refrigerator Door Shelf Bin

George from Cleveland Heights, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

bottom door seal won't seal right

R&R DOOR SEAL VERY EASY TO INSTALL THANKS TO ALL

Parts Used:

Refrigerator Door Gasket

MANUEL from LOS ANGELES, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Fridge started making a loud racket. Condenser Fan Blade then disintegrated to dust and pieces. The plastic had degraded significantly.

The repair itself total time was quick and easy. Since the original fan blade blew apart, it was only a matter of putting the new one on in it's place. This can be done by feeding the blade between the cowling and Condenser coil and applying pressure to get it on the shaft.

If your fan is still on the shaft, simply push it off and extract it the same way. Then place the new one on the shaft.

In my case, since the part would take a couple days to get, and I had food both in the fridge and the freezer, I removed and unplugged the Condenser Fan Motor and the cowling frame and temporarily spliced a small fan I had into the line for the condenser motor. This kept the fridge working long enough to get the replacement part.

Side note. Direction of airflow is towards the Compressor, and draws air across the Condenser coils.

Hope this helps someone. :)

Parts Used:

Condenser Fan Blade

Jack from WALLING, TN
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Socket set

4 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

One blade broke from condenser fan

The part i recieved, from parts select was a larger in circumfrence (<1/4) than the original. However i was not aware of this until after i treid to repair it.

I removed the broken fan from the condenser. This was very sipmle.

When i pluged the refridgerator back in to the outlet the fan tried to start up but soon began to make aloud noise, due to there not being enough clerance.

Parts Used:

Condenser Fan Blade

Chris from Lockport, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

12 of 31 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Ice maker would dump ice one time and then stop. Turning the ice maker off for a minute and back on would repeat the process.

I removed the two side mount screws with a screwdriver and disconnected the electrical plug to the ice maker to remove it. I reversed the process to install the new one.

It was the thermostat that was the problem, but I chose to replace the entire ice maker for only $25 more.

Parts Used:

Refrigerator Ice Maker Assembly

James from KNOXVILLE, TN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

i smell very bad smell coming from refrigerator

I started look inside ,disconnected power, and open all possible compartments to see any burned part. Fortunately I fined a small part look like melted and then i went online and make my research .Then i ordered that part and change it.

Parts Used: