FGHG2344MP2 Frigidaire Refrigerator - Instructions

remove back cardboard panel, cut off water supply, remove screws holding valve to back of refrigerator, unscrew water lines & reattach to same fittings on new valve, screw new valve in place, replace cardboard cover.

Installed new valve.There are several pieces of tubing coming off of the valve. Pay close attention to where they go. Color coordination is poor on the new valve.

Push in on filter and it releases pull filter out. Slide new one in push in and it locks it. Run water for 2 minutes and it is finished

it is a very simple process. pull out the water filter. put in the new one after removing the plastic tops. slide the filter in place pushing to set it in place. run water through water spout on door of fridge for about 3 minutes or until all the air bubbles are out. and there you are ready for a drink of water.

i was trying to figure it out but eventually it fix it self even when i get the part the problem seems to be fix on its own i unpplug the eletrical cord from the wall for over three hours and plugged back in and after 2 more hours it works so i am confussed dont know what happen i did not change any part so i have one brand new inlet water

Used a nut driver to remove the small panal from the back of the refrigerator. Removed the two screws holding the valve in place. Unscrewed the water lines from the old valve and cut the ends off of them. Push the water lines back into the new valve. Unpluged the wiring from the old valve and installed them in the new valve. reinstalled the new valve and put the cover back on. Tested system for proper operation.

Used socket set and screw drivers to attach ordered hinge, thankfully we had the screws just not the hinge. Wonderful to be able to find and order on line! Thanks so much!!!

Purchased a replacement part only to find the new part had push on fitting and my part has screw on fittings. Went to Youtube where Partselect had a video on how to replace the part from screw fittings to push on fittings

Removed new replacement crisper from packaging. Washed crisper in warm soapy water. Rinsed & dried crisper. Aligned crisper drawer with tracks on crisper shelf and slid crisper in until front panel was in home position. Slid crisper full travel in & out a couple of times to check not only for correct travel but also travel stops. Adjusted crisper setting, placed produce into crisper, closed crisper, & closed refrigerator. WARNING do not slam, drop, or otherwise mishandle crisper. It's only plastic!

Unplugged frig. removed old switch with the aid of screw driver. removed wires and taped; plugged frig. back in and waited for new one. new one came, unplugged frig.removed tape from wire clips plugged in to switch and pushed switch into socket hole and plugged frig. back in; shut door, works like a new one.

problem still persists part did not fix problem. made repairs recommended per your site.

Once the filter arrived, I pushed it in that releases a latch and removed the clogged filter. I then pushed in the new filter and when it clicked, I ran a few cups of water through it to clear any debris left from manufacturing and the job was finished. Less than 15 minutes.

The new inlet valve came with pisco connectors so had to cut the end of the tubes off. Before doing this I marked all the tubes to make sure they were replaced in the correct order. The pisco connectors are great to use and very quick. The total install time was about 20 to 30 minutes. While you have the back of the frig off make sure you vaccuum the fan and coils. It was making ice in less than 20 minutes.

Turned off the water supply ,pulled the plug removed two screws to access theater lines the new valve body was a little different than the original I had to cut off the end of each hose and push them in to the new connections the hoses are size and color coded replaced the two screws put the water line on plugged it in and turned on the water checked for leaks twice and replaced the back cover

I changed the valve but still no ice, changed the filter also. think it was just froze. could have saved me 70 bucks