This part is a replacement electronic clock/timer for your oven. The clock timer will display the time, and can be used to set a timer. If the clock will not start, will not allow you to program the t...
Sold individually. This part helps the flame to spread for even heat. Also protects your burner head from spills. The surface burner cap is located on the top of the burner head and is used in ranges ...
$39.23
In Stock
Questions And Answers for FFGF3052TSA
Ask our experts a question about this model and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Manuel
February 17, 2020
Oven turns on for a bit then shuts off
For model number FFGF3052TSA
Hi Manuel. This could be a faulty thermostat, or heating element. Thank you for your question and good luck with your repair.
2 people found this helpful.
Was this helpful?
Thank you for voting!
William
July 7, 2021
Why does the touch pad keep blinking f- 10
For model number FFGF3052TSA
Hello William, Thank you for the question. the F10 indicates that the control detects a runaway temperature in the oven and the Oven Temperature Sensor may need to be replaced. We hope this helps!
Oven is taking over 45 minutes to preheat to any heated setting.
For model number FFGF3052TSA
Hello, Thank you for your question. You will want to try and reset the unit by flipping the circuit breaker and then allowing it to sit like that for 1 minute. Once you flip it back on it should run properly. If not you may wish to check the elements, the sensor, and the control board.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Syed
March 19, 2023
When I plug-in my oven it starts beeping and display F08 error code. Can you tell me what this code is and how to fix it. Thanks
For model number FFGF3052TSA
Hi Syed, thank you for reaching out. Error F08 indicates that the oven control board is either not getting the proper voltage or is defective. Unplug the appliance for 10 minutes, and then plug it back in. If the error code reappears, the voltage will need to be checked on the control board per the wiring diagram. If that checks out, you may need to replace the control board, part number PS12717913. We hope this helps!
I am an HVAC tech by trade so it wasn't difficult to diagnose problem with safety valve. The hard part was being without an oven for a week. Repair was simple and effective--oven works good as new. Shut off gas and unplugged oven. Removed floor of oven between broiler and bake section, used wrenches to disconnect gas line from safety valve in back of oven, used philipps head screwdriver to remove burner assembly and gas valve, reversed process to replace. Checked out operation--OK.
The repair of the oven was really easy . I removed a total of 7 screws with a 1/4 inch nut driver to remove the back cover of the instrument panel. I then unplugged the wires from the from the oven control and with a phillups screw driver I removed 4 screws that hold the oven control,the face plate with the words on it has to be taken off the old control and put on the new one . I then installed the new oven control by putting the 4 screws back on and plugging back the wires. I then replaced the back cover with the 7 screws and plugged the power back in the outlet, The clock has to be adjusted and your done.
Turned off power, took back off stove removed old probe. I had to splice wires since new probe ends did not match up. the instructions were to splice the wires. I had the breaker off for about 3 hours. this is not in the instructions, but being a widow, I had to ask a few people why it would not come on after I connected the wires. After waiting, I turned the breaker on and my range came back on.