This kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant, and installation screws.
$56.05
In Stock
Order within the next 9 hrs and your part ships today!
The rear drum support bearing helps support the dryer drum to rotate quietly and smoothly during operation. The bearing attaches on the inside of the rear panel of the dryer cabinet. If your dryer is ...
$12.62
In Stock
Order within the next 9 hrs and your part ships today!
This thermal fuse limiter, with a limit of 220 degrees Fahrenheit, is manufactured for both gas and electric clothes dryers. Once the internal temperature of the dryer reaches 220 degrees, the heating element cuts out.
$22.95
In Stock
Order within the next 9 hrs and your part ships today!
This dryer lint screen is for laundry centers.
Dryer lint screen captures lint and debris from the exhaust air flowing from the dryer.
Follow the instructions in the owner's manual when installing this part.
$58.25
In Stock
Order within the next 9 hrs and your part ships today!
The pump is what your washer uses to remove the water from the tub. This part is the pump and motor assembly which includes the red flapper to prevent drain back flow.
$275.78
In Stock
Order within the next 9 hrs and your part ships today!
The upper felt seal for your dryer is attached to the top edge of the drum support area, and is held there by a high temperature adhesive. It creates a seal where the dryer door opens and closes, so t...
$46.95
In Stock
Order within the next 9 hrs and your part ships today!
Order within the next 9 hrs and your part ships today!
Questions And Answers for FEX831FS0
Ask our experts a question about this model and we'll get back to you as soon as possible!
7 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Loise
July 3, 2022
The tub is not filling with water to rinse please help.
For model number FEX831FS0
Hello Loise, Thank you for the question. If water is filling during the fill cycle but not the rinse cycle, this could indicate the timer switch is not going through the cycles properly. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
Hello Barbara, thank you for reaching out. Based on our understanding of the issue, we would suggest checking the spin bearing, part number PS446536, to solve the problem. Glad to be of help!
Do you happen to know the washer and dry capacity for this Electrolux washer/dryer combo? The washer is spinning, but not agitating.
For model number FEX831FS0
Hi Leonard, thank you for reaching out. We have researched and found that the washer capacity of this model is 2.7 Cu. Ft, and the dryer capacity is 5.7 Cu. Ft. To solve the issue, you may first need to make sure that the washer is not overloaded and the agitator is not stuck or damaged. If the issue persists, you may need to check the agitator drive block, part number PS1152574, as it is most likely faulty and may need to be replaced. When the drive block breaks down due to wear and tear, the agitator stops working. Please contact us anytime if you require further assistance!
Hey David, thank you for reaching out. We have researched your model number and found that Water Inlet Valve, part number PS815533, is compatible with your model. We hope this helps! If you need help placing an order, customer service is open 7 days a week. Thanks again for your great question.
well, i started at the top and worked my way down. by taking the top off, it gave me more room to get the dryer tub out. took the two screw`s out of the vented plate on the back of the machine to undo the belt. this is a stackable washer-dryer combo, so next i took off the white plate on front between washer & dryer. took off the control panel, unpluged it, then took dryer door front off. then removed the two screw`s that hold that bracket on ,in the back of dryer, pulled the drum out & replaced the belt, but before replacing anything i took the shopvac to it , there was alot of lint in there.when replacing the Grounding Ball Clip & Grounding Ball, i took a one inch by two inch magnet and used it to hold the Grounding Ball & Clip in place so i could get the two screws started in the Drum Support Bearing & Bearing Bracket. after installing that i put the shaft in place & lined the dryer tub up with the 3 screw hole`s ,and boom, bang, pow...nothing to it. it`s easy...parts came very fast....Thx PartsSelect.com...i`ve told all my friend`s about PartsSelect
1. Unplug dryer from outlet 2. Using Lg. flat screwdriver, pry under the front edge of the top and release two spring tabs 3. Lift up top and tilt back out of your way 4. Unscrew two phillips scews on inside of front panel 5. Lift up and out the front panel. Two spring clips at bottom. 6. Rlease tension on drum belt at the motor. Access panel at rear of dryer. 7.Unscrew 3 screws from inside, center rear of drum. 8. Remove drum through the front of the dryer. You may have to spread the sides apart a little bit for it to fit 9. Lift up on the rear drum bearing to remove it from the bearing retainer. ( U shaped plastic socket) 10. unsrew 2 screws and remove the bearing retainer, ground ball. Ball retainer is on outside of dryer. 11. Vacuum everything--duct, blower, lint trap, ect. 12. Intall new bearing retainer and grounding ball, an assistant is helpful at this time, one to hold ball retainer on rear of dryer, one to screw it in from the inside 13. reassemble remainder of parts in reverse order.
carefully pry up on front washer top to release plastic keeper pins,remove 2 phillips screws from beneath lower front washer panel,slightly lift upward on panel to release.remove old broken belt,push new belt beneath large tub pulley,put belt on small motor pulley,push back belt tension /idler arm,start belt on large tub pulley,turn tub pulley by hand to run belt on,release tension on idler arm.replace front panel and lower top.WALAAH!!!! you are done.
