This kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant, and installation screws.
$73.24
In Stock
Order within the next 6 hrs and your part ships today!
This thermal fuse limiter, with a limit of 220 degrees Fahrenheit, is manufactured for both gas and electric clothes dryers. Once the internal temperature of the dryer reaches 220 degrees, the heating element cuts out.
$34.73
In Stock
Order within the next 6 hrs and your part ships today!
This dryer lint screen is for laundry centers.
Dryer lint screen captures lint and debris from the exhaust air flowing from the dryer.
Follow the instructions in the owner's manual when installing this part.
$106.05
In Stock
Order within the next 6 hrs and your part ships today!
The pump is what your washer uses to remove the water from the tub. This part is the pump and motor assembly which includes the red flapper to prevent drain back flow.
$211.11
In Stock
Order within the next 6 hrs and your part ships today!
The upper felt seal for your dryer is attached to the top edge of the drum support area, and is held there by a high temperature adhesive. It creates a seal where the dryer door opens and closes, so t...
$25.26
In Stock
Order within the next 6 hrs and your part ships today!
Order within the next 6 hrs and your part ships today!
Questions And Answers for FEX831CS0
Ask our experts a question about this model and we'll get back to you as soon as possible!
24 questions answered by our experts.
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
James
December 15, 2019
The dryer has started making a high pitched squeal when turned on. At first, it was random and would go away after warmed up. But now, the screeching sound is continuous. The unit is over 10 years old, but has worked great until now. Your thoughts?
For model number FEX831CS0
Hello James, thank you for your question. That type of issue is usually caused by the PartSelect Number: PS3408299 belt and rear drum bearing PartSelect #: PS459829. I hope this helps!
7 people found this helpful.
Was this helpful?
Thank you for voting!
Rodd
February 4, 2020
Washing machine won’t automatically go through it’s cycles. It has to be turned manually.
For model number FEX831CS0
Hello Rodd, Thank you for the question. This sounds like the Timer PartSelect Number PS418697 is defective and will need to be replaced. We hope this helps.
Could you please tell me the capacity of the wash tub and the dryer? Also, two other issues. 1-. dryer makes loud screeching noise when turned on, then noise quites in a few minutes. what part would i need? since it's 15 years old i don't want to put too much into it. if i continue to use without replacing this part, will it cause furthur damage? 2-. i have taken dryer apart when i bought it used and cleaned lint out thoughly. it still leaves much lint on clothes. vent does collect well and properly seeled. lint chunks hand up in door, but lint still on clothes once they are dry. any possible solutions? thanks much.
For model number FEX831CS0
Hi Jan, thank you for your question. Both are 5.7 cu ft. For your dryer you may want to check your felt seals and your ball hitch bearing. It could be that one or all of those parts have worn out and just need to be replaced. If you are getting excessive lint on your clothes you may need to clean the filter with some hot soapy water. It might be that it is clogged. You may also want to check the inside ducts of the appliance and make sure there is no build up on lint inside of the dryer duct itself. Good luck with your repair.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Steve
January 3, 2023
The water does not shut off after filling washer
For model number FEX831CS0
Hello Steve, thank you for contacting us. There could be two probable reasons why the water does not shut off after filling your washing machine. It is possible that the water inlet valve, part number PS815534, which controls the flow of water into the washing machine, is faulty or clogged. Another possibility is that the water level switch, part number PS1146954, which is responsible for detecting the water level in the washing machine and turning off the water flow when it reaches a certain level, is not working properly. Customer service is available 7 days a week if you require assistance placing an order. Thanks again for reaching out!
This stackable washer/dryer came with my rental condo but maintenance doesn't cover it and the washer is leaking from drain pump. What can I check before I call a repair service, Dryer is fine. How do I know if this is gas or electric?
For model number FEX831CS0
Hi Deborah, thank you for the question. Based on our research, it is an electric dryer/washer combo. For the leaking issue, you may need to check the drain hose for clogging and also check the tub seals for any damage. If both are fine, we would recommend replacing the drain pump, part number PS7783938, to fix the issue. We hope this information helps!
1. Unplug dryer from outlet 2. Using Lg. flat screwdriver, pry under the front edge of the top and release two spring tabs 3. Lift up top and tilt back out of your way 4. Unscrew two phillips scews on inside of front panel 5. Lift up and out the front panel. Two spring clips at bottom. 6. Rlease tension on drum belt at the motor. Access panel at rear of dryer. 7.Unscrew 3 screws from inside, center rear of drum. 8. Remove drum through the front of the dryer. You may have to spread the sides apart a little bit for it to fit 9. Lift up on the rear drum bearing to remove it from the bearing retainer. ( U shaped plastic socket) 10. unsrew 2 screws and remove the bearing retainer, ground ball. Ball retainer is on outside of dryer. 11. Vacuum everything--duct, blower, lint trap, ect. 12. Intall new bearing retainer and grounding ball, an assistant is helpful at this time, one to hold ball retainer on rear of dryer, one to screw it in from the inside 13. reassemble remainder of parts in reverse order.
carefully pry up on front washer top to release plastic keeper pins,remove 2 phillips screws from beneath lower front washer panel,slightly lift upward on panel to release.remove old broken belt,push new belt beneath large tub pulley,put belt on small motor pulley,push back belt tension /idler arm,start belt on large tub pulley,turn tub pulley by hand to run belt on,release tension on idler arm.replace front panel and lower top.WALAAH!!!! you are done.
Unplugged Dryer. Opened top of Dryer, over the drum. Removed Thermal Limiter. Tested the Thermal Limiter - found it was open. Checked all vents and exhaust tube for lint build-up. Replaced Thermal Limiter. Closed top of dryer. Plugged Dryer back. Tested Dryer - it works.