All Installation Instructions for Roper Range FES355RQ1

Bake element was broken

Remove the old part and install the new part.

Parts Used:

Oven Bake Element

Range Screw (Grnd Wire / Back)

Alexander from LINCOLN, NE
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Broiler element burned out

After doing a YouTube search. I successfully completed the repair by easily diagnosing the issue with the element.
I watched a video about 5 most common problems with whirlpool broiler elements.
The first being to inspect the element for damage. I found a small section that appeared to be rough and had a raised bump.
I decided to order a new element because the oven is older and it wouldn’t hurt to install a new one even if this wasn’t the issue.
Once the part arrived, which it did quickly, I followed the video instructions. It was easy and straight forward. I completed the task in under thirty minutes. It was very simple and I now have a functional broiler element.

Parts Used:

Broil Element

chris from HILTON HEAD, SC
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Extremely easy repair

Unplug stove. Remove the two screws attaching the element to the rear of the oven. Carefully pull out. Disconnect wires. Reconnect wires. Screw back in. Done. The hardest part was moving the stove away from the wall.

Parts Used:

Oven Bake Element

Melissa from MILL CITY, OR
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Replacing the bulb in the freezer side

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Parts Used:

Light Bulb - 40W

Yafa (and David) from Bothell, WA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

5 of 11 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven not reaching temperature

Simple-pulled range away from wall, unplug from socket. Removed back panel unscrewed thermoses and replace. Put back panel back on plug in, tested temperature setting before sliding range back on place

Parts Used:

Oven Sensor

Marsha from Clermont, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Paint peeling from strip

removed 3 screws holding the strip and replaced with new strip

Parts Used:

Range Trim Lower (White)

Myron from Punta Gorda, FL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Old lower element fell apart

1. Unplug the power
2. Unscrew the two screws that hold the element
3. Pull the element out a little to expose the wires.
4. Gently pull off each wire (best done with needle nose) MAKE SURE THE WIRES DONT FALL INTO THE BACK OF THE OVEN.
5. Firmly seat wires back onto new element and replace screws
6. Bake stuff!

Parts Used:

Oven Bake Element

Matthew from MIDDLETOWN, CT
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Baking element had burned into

The video was very helpful.

Parts Used:

Oven Bake Element

Rebecca from LANCASTER, SC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven bake would not heat up at all.

Very simple.
Remove 2 mount screws using a #2 phillips screwdriver.
Pull the element out to expose the 2 wires.
Using pliers, slip both wire terminals off the existing element.
Push wires onto the new element and install both mounting screws..
Done!

NOTE: The existing element showed no exterior signs of being bad.
The damage must have been internal.

Parts Used:

Oven Bake Element

Wilton from CANYON LAKE, TX
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

I was trying to remove the oven door so I could clean the glass. Spills had run down between the layers of glass.

This oven probably was manufactured in the '60s when the house was built. The door doesn't just pull off like the newer models. These pins fit into small holes on the oven hinges. I inserted the pins and lifted the door to a 45 degree angle, before pulling the door completely off. Now that turned out to be the easy part. I then proceeded to completely dismantle the door. It actually has 4 glass layers which had to be cleaned individually. The hardest part of all was actually remembering how to put it back together again. I put the door back on just as I had removed it, then took out the pins, and I was finally done! This was not an easy project, BUT the results look great.

Parts Used:

Hinge Pin Kit

Karen from Oklahoma City, OK
Difficulty Level:
Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers

3 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

could not control the temp of the element

take off back panel, simply unplug the old switch and plug in the new one. Simple

Parts Used:

Infinite Switch - 6 Inch

Steve from GREENBRIER, TN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

the fastener became loose and dropped into the stove

This is a cook stove that is used 5 months a year. We have not fixed it yet because we are now in Florida the stove is in New York. We ordered that part just before we left NY for FL so the repair will be done in June of 2021.
George Clark

Parts Used: