All Installation Instructions for Frigidaire Range FED300ESE

Surface element shorted out

Tilted the surface unit and proped it up with the metal arm then I unpluged the old 8"-surface element and replaced it with the new 8"-surface element that I purchased from PartSelect.com. I then lowered the surface unit turned the burner knob on and everything worked fine. Thanks PartSelect.com.

Parts Used:

Surface Element - 8 Inch - 2600W

Claude from Baton Rouge, LA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Existing stove top burner element worn out

Very easy to repair! I removed the old burner and slid the new burner element in its place. It was as simple as that! No tools required. My one and only complaint would be that the old burner was slightly larger (within 1 inch or so) than the new one so the new one sits slightly crooked on the stove top. But it works just fine. The item also shipped very quickly. Within a day or two. I am very satisfied with the transaction overall.

Parts Used:

Surface Element - 8 Inch - 2600W

TRACY from EASTON, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Intermittent heating element function

Instructions included with terminal block assembly. Toughest part was to strip the insulator off of the old wires on the stove. I was originally going to just purchase one but after looking at the other terminal blocks and seeing the burnt insulation and some of the wire strands, I just replaced all 4. PartSelect customer sevice was very helpful to confirm the correct part number I needed for my stove.

Parts Used:

Terminal Block Kit

Jeffrey from Pittsburgh, PA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Renewed drip pans

Replace the old ones with the new ones. Was VERY impressed with the quick delivery!!

Parts Used:

Drip Bowl - 8"

Chrome Drip Bowl - 6"

Frank from Winter Garden, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Control will not work - only clock blinks

Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

Parts Used:

Main Terminal Block Kit

Sue from Lampasas, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers

0 of 4 people found this instruction helpful.

Was this instruction helpful to you?

heating elements not working

prepared the parts as directions displayed, removed the heating coils and popped the hood on the range, simple curcit 2 wires in to the main harness for each coil. snip, plug and twist add heat wrap to seal the new conections and done very simple fix saved me buying another oven....for now

Parts Used:

Terminal Block Kit

christopher from cincinnati, OH
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

1 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Broken globe in oven and burnt out light bulb

Easy as 1-2-3

Parts Used:

LENS

Light Bulb

Sharon from Foley, AL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Oven was not heating up to the set temperature. Stopped around 180-200F.

Removed 2 screws holding old temperature sensor inside the oven and gently pulled out the wire till the connector came through the hole. Disconnected old probe and attached new one. Fished the wire back in the hole and replaced the two screws. Then followed the operating instructions for calibrating the oven. Ended up setting it +5 degrees. So far, works great.

Parts Used:

Temperature Sensor

Robert from Glasgow, MT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Oven did not work since bake element did not warm up.

Square drive screws used throughout the oven since its manufactured in Canada. Shut power down to the range. Element fastener plate removed and 2 electrical terminals loosened. Used a pair of hemostats to hold on to the wires so as not to lose them to the interior back of the oven which was loaded with insulation. Connected the 2 wires to the new element, screwed the element fastening plate with element back to the back of the oven wall. Turned power back on and voila, I was back in business.

Parts Used:

Oven Bake Element

Russell from North Smithfield, RI
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Bake element went out on my oven

Took a screwdriver and removed screws attaching the element to the back of oven. Disconnectec the wires from the old bake element. Replaced the new reversing the process. Very easy.

Parts Used:

Oven Bake Element

Jeffery from Union Point, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

lower oven element burned up

Used a screw driver to loosen 2 screws and the pulled the tabs off the old element and installed the new element. I am probably the most "unhandy " guy in the world but this was a snap. I am as surprised as anyone.

Parts Used:

Oven Bake Element

Constantine from Vero Beach, FL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

element not heating right

Took old one out and plugged the new one into place.

Parts Used:

Surface Element - 8 Inch - 2600W

sharon from Summerton, SC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Replaced burner drip bowl

Very easy to remove the old drip bowl and replace with new ones.

Parts Used:

Chrome Drip Bowl - 6"

Drip Bowl - 8"

Irene from Rochester, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Coil melted in half.

First. shut off the power!!! Remove the two screws holding the coil. Next- slightly pull remaining wire to access the plugs. Unplug the wires, remove old coil, replace and plug in the new... Replace two screws.... Turn power on and....... Start cooking! EASY!

Parts Used:

Oven Bake Element