FDPC4221AS0A Frigidaire Dishwasher - Instructions

If you are getting intermittent leaks especially when you put a pot lid up front, it’s probably just the door gasket. And this was the easiest project I’ve tackled as a homeowner since buying the place 20 years ago. I read the other stories and I think the suggestion I choose to follow is not the best thing to do. So, read passed where I cut the gasket. I used needle nose pliers to grab the bottom edge of the old gasket which then pulled out by hand with almost no effort. I used the old gasket to measure the new gasket as recommended in one of the other stories, and cut it. DON"T DO THIS. The gasket is very soft foam rubber. As you push it in (I just used my fingers), it will get longer as you push it in. I put it in the first time (took about a minute if that long) and even though I cut it to the same length as the old one, it was too long. Obviously I figured I did something wrong. So, I took it out and measured it again. Nope, same-same. So, I put in a second time, careful not to stretch it, and this time it was now too short. So, I recommend that you just establish the bottom edge 90 degree angle seat and try not to stretch it as you work your way around the seam. It should fit just find, maybe with a little adjustment back or forth, but without cutting it at all. By the way, the half inch I cut off at the recommendation of one of the other reviews did not ruin it. It works just fine. So you can cut it if you want I suppose. But that half inch I cut off was what I was short when I was carful not to stretch it.

First point of leakage was the door. Turns out that a gasket at the bottom of the door functions as a wave trap. As the bottom sprayer spins it sprays against the door and creates a small wave of water this gasket was starting to disintegrate, it was letting water surge over the small tray at the doors bottom. Easy to replace just pull down and remove press fit on inside door bottom. Only when this was replaced did I find the real leak but not until I guessed at the tub seal as the leak. Very hard to see where the water really comes from! Turns out it was not the tub seal but a clip that holds the heater element got smashed down from a dropped dish rack at some earlier time and this caused the heat to increase at the clip and eventually heat the clip to extent it melted the tub directly under it. JB Weld to the rescue and we have a waterproof tub again. Well almost! The tub gasket resisted my best efforts to seat correctly and thus required a new tub gasket, still hard to seat but after 2-3 attempts we have a winner. Total cost about 50 bucks vs. 6-700 for a new unit. Wife is happy!!

Turned off elecrtic and water to dishwasher and pulled dishwasher out from under cabinet. Removed broken hose using pliers to open hose clamps.
installed new hose.

It only took about 20 minutes to replace. Thanks for the video.

My husband and dad actually did the repair, but my husband not being a handy guy said it was, 'so easy, anyone could do it!' He was very nervous about taking on the project, the longest part was testing to make sure it worked(running a cycle).
The simply pulled out the dishwasher, after disconnecting all electrical power, drained the rest of the water that we couldn't see from above, following the video given took out the old part without needing to take out the motor and were able to replace the drain pump, put everything back together besides sliding it into place in case it didn't work, in less than 15 minutes! When the short cycle finished and the water had drained they put it back into place and ran an energy saver cycle and it worked like a charm! Since then(2 weeks ago) we have now ran every function and have had no issues! Every time we open the dishwasher we comment on how much we missed having a dishwasher! Haha!

Removed the bottom panel, and I had to disconnect the water supply, which did NOT use flexible tubing (much to my disappointment), removed the screws holding the diswasher in the cabinet. Slid it out, took the old springs off, put the new ones on.

It was pretty straightforward -- no big deal.

Removed damaged strike plate from dishwasher and screwed new part into place. Tested and dishwasher worked fine. Took less than 15 minutes to get the job done. Was very pleased with how fast the part was delivered.

VERY simple---unscrewed three screws on the broken part (the little nubs that held on the bottom spinner were broken off), screwed the new one back in, re-attached the spinner.

I was VERY pleased with the customer service and quick shipping (ordered on Sunday night, the part was delivered Wednesday morning). I would definitely recommend this site to anyone, and would use it again. Five Stars!!!!

My daughter held the flashlight steady as a rock as I hooked not one, but two new hinges in place. Throughout the whole ordeal neither of us complained or lost our resolve. We conquered!

1-2-3 snapped off the old and snapped on the new! New part was just as ordered and just like original! My dishwasher is like new again! Thanks PartSelect for your great price and prompt shipment!

It was super simple. I popped the clips that were holding the old spray arm on and then popped the new one in place.

I read the instructions that others had posted and completed the repair in less than 5 minutes!

Pulled old gasket off with small hook. Replaced new gasket by pressing in with my fingers.

Replaced upper wash blade and used screwdriver to pop off rail stops to slide rack all the way out to exchange

Removed all sealer and install new one as instructed.