FDE436RES0 Frigidaire Dryer - Instructions

Almost exactly as per the videos available on the PartSelect web site. The only additional information that would help is that the vent on the back of the unit can be removed to allow for access to the belt spring pulley. This avoids having to reach around from the front of the unit and feel your way to remove and re-install the belt.

Very easy and straight forward repair.

Unplug the dryer and move it to a location that offers some room to work.

Use flathead screw driver to pop the front side top of the dryer up then lift the top of the dryer up to expose the drum.

Use phillips head screw driver to remove the two screws from the access panel on the rear of the dryer. Reach into the access area and remove the drum belt from the tensioner assembly. It's spring loaded so watch your fingers.

Disconnect the wiring harness at the right front of the dryer.

Remove the two screws that secure the front of the dryer to the sides.

Remove the front panel of the dryer by pulling the panel forward then up and off the two tabs at the bottom.

The felt strips and glides (which are worn off if you are doing this repair) are glued to the front panel of the dryer and now need to be removed. Removing the old felt will take some time and is the most difficult part of this whole repair.

Use some goof off or similar solvent adhesive remover to ease the removal of the felt. A putty knife will likely be helpful too.

Once the felt is off, wipe off any excess solvent and make sure the area to be re-felted is clean and dry.

Apply small serpentine bead of provided adhesive to the felt strips and glue the new strips on to the dryer. There is more than enough glue in the tube provided to get the job done. After applying felt strips, let them sit for about 30 minutes before reassembling dryer. You may want to use some light duty clamps to hold the felt in place while the glue sets but that's probably not necessary since the glue sets rapidly. Follow the directions on the glue tube.

Reassemble in opposite order.

Take the opportunity to vacuum out your dryer and give it a good inspection while you have it cracked open. You just might find those socks that disappeared.

Here are some "while your at it" ideas:

Replace both upper and lower felt strips.
Vacuum out entire dryer cabinet and the foam seal on the air box.
Replace drive belt.
Replace light bulb.
Replace bearing ball on rear of drum or apply some lubricant to the bearing.

I'm not saying do all these things, I'm just suggesting these items as things to consider based on the age and usage of your dryer.

This is an easy one person repair that requires no experience or special tools. Don't pay the repair man. Do it yourself.

I took the repair video in with me and set my lap-top on top of the washer.
My dryer did not match the type on the video exactly (mine has the controls in the front instead of on top and in the back) - however - the parts replacement for the rear drum bearing itself was the same.
After getting the front apart and releasing the drum the rest was pretty easy. Didn't really need instructions for the heating element - that was an obvious change out.
The tips on the video changing the rear drum assembly were very helpful.
Just watch the vid and do it! It took me exactly two hours since I was also changing out the heating element and I did it on a Friday night while having a couple tasty beers.
One tip I would give is the old grease in the bearing is very messy and I got it all over my shirt and pants - and when changing that stuff out don't lean on the front of the frame - I did and bent it out of whack a bit.
The dryer runs like new now that it's done!

All I did was push the new part into the machine! So easy!

1 Unplug the dryer and Raise top up by releasing the clips and fold back to expose the drum. 2. Take Phillips head screw driver and remove two screws inside the front dryer panel and then take flathead screwdriver to pop out both sides and set aside. 3. Lay on your stomach and reach inside to the belt pulley and push right so the belt will release then stand to either side of dryer and grab the belt and lift the drum up out of its bracket. 4. Go to the front and pull the drum out and replace the Rear Drum Bearing Kit . 5. Grab the front panel and remove the Top dryer guide and replace to match evenly with the bottom dryer guide by cutting at least 1/8 -1/4" from felt and use High temp adhesive to glue down. 6. Replace everything in order that was taken apart and reconnect electrical plug and start dryer.

used a putty knife to press the clips away from the door and lift the assembly away out of the door. Used the putty knife to push the clip over the lip and snap the new handle into place

The new motor from parts select was not correct. The new motor is a bolt on. The original motor was a press on. Had to return at a cost of 42.00 dollars. Had to buy a new dryer.

put the new one on

1. Lift the dryer top off to get to the two screws holding the front of dryer. 2. On the back bottom left of the dryer, remove the vent so you can get to the tension pully to loosen the belt around the drum. 3. Remove drum. 4. Disconnet element coil from wires. 5. Carefully remove element coil from ceramic holders. 6. Get new element coil and attach to wires while carefully keeping coil loose and untangled. 7. Again, carefully restring coil into ceramic holders without springing the coil making it misshapen. Once all of the coil is in the holders, retrace your steps. 8. While you have the appliance open, it's a good time to vacuum out all lint to prevent a fire from occuring. 9. REMEMBER TO ALWAYS UNPLUG THE APPLIANCE BEFORE WORKING ON IT!

I remove the old lint filter and just put the new one in.

i first looked up the diagram for this model and checked for the best way to take the front cover off the dryer. after removing the front cover i start looking for the wires that connect the door switch and remove the wires. the front cover also supports the weight of the drum, so carefully pull the cover until the drum comes loose. at this point you can visually see the parts of the parts that make up the workings of the dryer. i first noticed the drum was coming out with the front cover at this time i knew the rear drum assembly was broke. i then took the belt loose from tension pulley and slid it off the drum and removed both from the cabinet. after the drum was removed i also noticed the heating was broken in several places. i removed four screws from the heating element assembly and also removed two wire that were connected to the element. with all pieces removed i checked the thermal switches, there are three switches, one on the heating element, one on the vent side and one on the back panel of the cabinet. i then installed the rear drum assembly and the heating element assembly and connected the wires. i then slid the drum almost all the in place and put the new belt around the drum and dropped the rear drum into the bracket that supports the rear drum then run the belt around the tension pulley and around the motor pulley. i then placed the front panel back in place and connected the wires for the door switch and lifted the drum assembly up just enough to insert the front panel door support into the drum and placed the clips in place, checked all connections twice and connected power back to the unit and turned on and run it through all its settings.

I removed dryer exhaust hose.unsnapped top cover the clips are in front and exposed inside of dryer,remove 2 screws on inside of front cover and set aside. remove lower cover in back and push belt extender until belt is loose remove 3 screws on inside of tumbler. remove tumbler out the front of dryer be careful not to damage belt set aside remove ball plate by pulling up and out it will unsnap. Now remove 2 sets of wires that are connected to heater element plate remove 4 screws holding element plate in place. Since dryer was all exposed I cleaned everything out with a wet vac put back together following instructions in reverse. Good luck

Watched on-line video, then applied those steps.
1. Pop the front of the deck loose using putty knife to depress clips;
2. Disconnect wires from light and door switch;
(Before I disconnected wires from door switch and light, I made wiring sketches to make sure I reconnected in original manner.)
3. Remove lint filter mount screws and mount from bottom of door opening;
4. Cut drum belt with wire-cutters and removed it;
5. Remove drum support clip from top center of front panel;
6. Remove (1) screw from each side of dryer body that hold front to sidewalls, removed front panel;
7. Remove drum by lifting the rear out of the bearing, then moving it forward through the machine front;
[While I had the dryer disassembled, I thoroughly cleaned it of lint, dirt & metal filings. The metal filings were from the worn ball hitch and drum support bearing cup. I spent as much time cleaning it out as I did working on it.]
8. Stand drum on gallon paint bucket while removing ball hitch (Use a #2 drywall phillips apex to obtain sufficient seating & torque to remove and reinstall ball hitch screws at rear of drum.);
9. Have a second person hold the new ball hitch in position while starting screws, if necessary;
10. Use nut driver w/5/16" socket to remove bearing retainer & ground ball clip;
11. Install new bearing into retainer clip, insert attachment screws through the holes in both, stick grounding ball in depression on back of bearing as screws are fed through back panel;
12. Hold ground ball clip in place to start one screw, then the other & tighten with nut driver;
13. Start drum belt on motor shaft and position against tensioner pulley;
14. Feed drum through front of machine and loop belt over rear of drum;
15. Slide belt forward on drum as drum moves to rear to keep it aligned with position of tension pulley;
16. Lift rear of drum to place ball hitch on top of bearing, then press down to seat it into bearing;
17. Turn drum to ensure belt alignment, then re-accomplish steps 6 thru 1.

I followed the recommendation from William, from Ardmore, OK and Elvis, from Miami, FL for the repairs. Elvis had detailed instructions as well as William, so I just combined the two and I was able to repair my dryer in three hours time. My sincere thanks to partselect web site in posting the repairs on line and for everyones input. I will be back to use the web site again to troubleshoot my other appliances and order parts (great price, fast service for parts) and I will highly recommend this site to my friends.

Followed your website repair guides and the great belt replacement video.

Other parts used were; front lower basket seal, dryer seal, and dryer drum belt.

Had no problems except for keeping the drum belt idler pulley tension spring in place. Used the rear access panel to solve this issue.

John H.
Palm Desert, CA