FDB736GFS5 Frigidaire Dishwasher - Instructions

Manually took off melted parts and replaced them with the new ones.

Intuitive repair if you are one of those people that take things apart & put them back together for kicks. Nothing fancy about this repair, as all the parts have no adjusting. Remove the 6 phillips heads screws on the inside of the dishwasher panel. The front electric panel comes off, leaving the inside exposed with the wires. Unhook 4 wires to the handle. Remove (2) star shaped screw headed screws. (The most difficult part if you don't have this bit.) New handle can only go in one way. Re-attach wires & screw panel back on. The latch required pulling the dishwasher out a couple inches from under the countertop to access the mounting screws. The dishwasher is held in place with 2 screws into the countertop/or side cabinet. Slide dishwasher out. Remove 2 screws and replace. Once again, there is only one way the latch can be installed. All is good, and easily accomplished in 5 minutes....if you have the "star" bit, which does come in a couple different sizes.

replaced with new lower rack, out with the old, in with the new! Shipping was great new part arrived in 2 days! Great service, and will use again for all parts needed in the future, and will tell everyone about this site! Thanks a bunch!

The nut was split down one side, so I first tried to sauder the nut back together. Saudering never goes well for me anyway, but I couldn't get a good enough seal around the nut to make it fit tightly. Then I had to cut off the clear plastic shield to get down in there, just before realizing you could just pull the white wire firmly and it would come loose from the nut. All I had to do then was unscrew the original nut, and screw on the new nut. Then, luckily I had mistakenly ordered an extra clear plastic shield and could replace the one I had previously cut. Dishwasher now runs like a charm!

The repair went very easy. Just opened the door , and pulled out the worn seal. Lined up the new seal and carefullly pushed new seal into place. Seal pushed in very smooth.

I took out 6 screws, the face plate just hung down. Make sure the breaker is off. there were two screws that held the switch and handle in place took those two out. Disconnected the four wires on the microswitchs and placed them on the new handle. Put the diswasher back together. Turned breaker on and worked great. But it started to leak. This is why they give you the gasket. The new latch does not always match to the same seal o the gasket. Replaced the gasket took less them two min. Ran the dishwasher again no leaks and the handle you can use one finger to unlock.

Delivery of this part was really fast. I ordered very early on a Thursday morning and the package was at my house Friday afternoon. This was a pretty simple repair. First you take the front panel off. There is an upper panel where the controls are and a lower finished apnel. Open the door, the screws are on the inside face of the door. Put a towel on the floor so the panel doesn't drop and scratch the floor or get damaged. Unscrew the panels so you can get to the door handle, it is held in with two torx screws (star shaped head). Take the handle off and remove the wires on the door switch. Installation is the reverse, mind that you install the wires on the right leads. The handle works better than the original ever did.

I turned the power off at the circuit breaker. I then took the access panel off the dishwasher at the bottom. I pulled the wire off the connector. I used a plied to remove the broken washer and replaced with new part. I put everything back in reverse order and ran the dishwasher. I than checked for leaks over two days while the machine was running and everything was fine. Thank you Parts Select for saving me $500!

New right away when we heard the sound, the spring broke. Easy to replace, pull dishwasher out from under countertop, usually held in place by two screws into countertop. Remove screws, pull out dishwasher. Close door, springs will now have the most slack in them. One spring located on each side. Remove spring from one side and replace with new spring to ensure proper spring placement. No actual tools needed as spring rests on a bracket attached to door and other end of spring goes through hole in bottom of dishwasher rack. open door to test for tension as there are several holes to choose from. .

Simple repair.

Very, very easy. Pop off the old wheels and snap the new ones into place on the rack.

Took off front door panel with two screws. Found the part in the door. took it out and slide the new part in. My husband screwed the screws while I held the door in place. If I had known it was so easy to do I would have done it as soon as I got the part but I waited for my husbands help.

Lower the door and remove bottom dish tray. Feel with fingers the area where gasket will be pulled from (just below bottom door edge) Pull old gasket from door edge into direction of inside dishwasher. Insert new one in same orientation as old (small slit to right side). New gasket strip will seat into door bottom.

Removed front of door to see how gasket was installed. removed door for proper cleaning of gasket area, removed old gasket cleaned area and installed new gasket in holder notch, reinstalled door adjusting alinement, reinstalled door front.

I just did the repair just like the video suggests to fix it. I disconnected the power cord, shut off and took apart the water inlet line, and drain line. Unscrewed the top of the washer from the cabinet and pulled out the dishwasher. Tilted the washer to better get to the bottom and took off the connecting wires (red and white.) Unscrewed the brass nuts holding the heating element and removed the element from the machine. Took out the bottom sprayer arm. Replaced the element, replaced the brass nuts and connected the wires back up. Put the sprayer arm back in. Pushed the machine back into place and re-secured the top to the cabinet. Hooked all water, drain, and power lines back up and all was good again.