FBD2400KB4A Frigidaire Dishwasher - Instructions

First of all, I got the part 24 hours after I ordered it. That in it self was a feat. Second, I followed everyone elses instructions, pulled the old gasket out with a pair of needle nose pliers, cleaned the area as good as I could, found the notch for the slot on the gasket to slide into and viola...it slid in and stayed in. No more leakage whatsoever! Thanks for all of the tips!

Pulled off the old gasket and replaced it the same way with the new one.

The old gasket was worn. I pulled out the old one, put in the new gasket. I trimmed the ends to fit and that was it.

pulled out dishwasher ,left lines hooked ,started cicle .heard pump.took apart.seen problem. order new one ,works like new..

if the wire they snap on was bent it needs to be straightend.......they just snap on. easy to install but wish they had better wheels so this problem would be solved. My 2 sons have same brand dishwashers and have same problem.

Had trouble installing the new gasket at first. Fell inside the door, and would not stay in the groove intended for it. After watching the video on your website, learned is best to angle the gasket and work in slowly to the groove from one side. Much easier then

My dishwasher started leaking at the beginning of the summer. We didn't know what to do, but didn't want to call an appliance repairman. Towards fall, a friend came over and pulled it out and found the heating element brass nut which was broken. We put it back in and washed dishes the old-fashioned way for another 3 months after that. I asked at my local hardware store for the part, and thought about trying one of those big-box do-it-yourself stores but never got around to it. Finally after getting sick and tired of doing all the dishes in the house by hand, I found your site, and the part I needed and ordered two (just-in-case). A few days later, we got the part, I pulled the dishwasher out again, screwed on the new nut by hand and put it back into place. We're in business!

I snapped the new one into place and ran the cycle. This time, everything came out clean, except for the bowl that had caked on cinnamon from the weeks I didn't have the part

Simply pulled old gasket out with hand, and slid the new one in place!

Removed front panel of door, to get to the screws that hold the door on the hinges. Removed door, pulled gasket with pliers from bottom of door, not easy to get out because of mineral deposits. Had to push quite hard to get new gasket in. Put every thing back together and no leaks. I live in Alaska and I tried to order the part through Sears and they wanted $18.95 for shipping for a $12.87 part. The part with PartSelect was $14.92 but only $6.95 for shipping. I ordered the part on a Tuesday and recevied it on that Friday. We in Alaska get very tired of companies thinking we live on another planet. Thank you PartSelect.

Watching a YouTube video that was attached to an email, I was able to install my new dishwasher filter in no time without any tools. Thank you.

Used pliers to pull out the old gasket. New gasket snapped into place. Notice where notches in the gasket are when the old one is removed, so the new one can be properly oriented. It was not necessary to remove the door.

I followed directions from a video on this site and written directions in order to make the repairs. Pulled out the old gasket from one end with pliers . I cleaned out the slot in the door of any food or dirt and replaced with the new gasket. It was a very easy and quick repair that allowed me to use my dishwasher quickly. Thanks for the help.

1-2-3. Finished ! I had watched your video on how to !

I measured the length of the gasket, using the old one to measure the length. Cut it to that length and installed it. VERY SIMPLE TO DO! But it didn't stop my leak--turns out there was a small leak in the bottom of the tub that was easily fixed with some silicone. The dishwasher's like new now!