Models > FAFS4474LA0 > Instructions

FAFS4474LA0 Frigidaire Washer - Instructions

All Instructions for the FAFS4474LA0
91 - 105 of 165
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
machine would not cycle and would not drain
I read other problems, I jumped the gun and purchased the door switch, this was easy to change, but MY machine still had the same issues, however, I found that the filter was plugged, and after I cleaned this out, this fixed my issues and the machine works fine, So I now have a door switch and striker should mine go bad, Hope this helps out
Parts Used:
Front Load Washer Door Lock and Switch Assembly Door Striker
  • Jeffrey from Cedar Rapids, IA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
plastic piece broke from door strike keeping door from closing and therefore the washer wouldn't work.
Ordered a replacement door strike which was easily replaced with Phillips screwdriver. I was very grateful that the part was so easy to find on this website. It was helpful that I had saved my book with model number of washer which allowed me to find the exact part needed. Thanks!!!!
Parts Used:
Door Striker
  • Rebecca from Frisco, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Broken Door Striker
Removed two phillips screws. Removed old door striker. Replaced with new door striker. Replaced old phillips screws. Job takes less than 1 minute.
Parts Used:
Door Striker
  • Robert from Hyattsville, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Replaced Door Strike.
Two screws out, two screws in.
Parts Used:
Door Striker
  • Lee from Kansas City, MO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The door strike just broke (who makes a plastic door strike on a machine that gets used as much as a washer?)
This was easy as pie. I unscrewed the old & put on the new. That's it!
Parts Used:
Door Striker
  • Dulcenee from Bloomington, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
broken doorlatch
Remove the top cover and the doorlacth and unplug the old parts as simple as that
Parts Used:
Front Load Washer Door Lock and Switch Assembly
  • ricardo from nesa, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Doors tricker broke
The repair was so easy!!! It took me less than ten minutes to remove the broken piece and to install the new piece. There were 2 screws to remove to get the broken piece off.
Parts Used:
Door Striker
  • Darci from Norwalk, CT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
door strike broke
Removed two screws and replaced the door strike.
Parts Used:
Door Striker
  • Edwin from Cape Coral, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Washer didn't start
I took off the top of the washer. It seemed easier than playing with the door gasket. It took about 15 minutes. Everything worked great. The washer is working again. THANKS PARTSELECT
Parts Used:
Front Load Washer Door Lock and Switch Assembly Door Striker
  • James from Whittier, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The top striker tip broke off....
Remove the broken striker, screwed in the new one in less than 2 minutes...this is the second time it was replaced...the first time I was still under warranty...he took about the same amount of time to install ...I ordered 2, because I know it will be broken again....
Parts Used:
Door Striker
  • teresa from brooklyn, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Washer would not go in high spin
It is a front load washer with a dryer stacked on top of it.Insaw a video on u tube. I took a neddle nose pliers ang took a spring loaded metal ring off that is holding the grey rubber boot on . I peeled it back just enough to reach ih and get the door lock in hand.I then took a phillip screw driver and removed the two screws un the front off holding the door lock..I then reversed instructions,and put the new lock in.The complete job took lease than 5 minutes,and the part did the trick. My washer works as good as new.
Parts Used:
Front Load Washer Door Lock and Switch Assembly
  • Randall from Doe Run, MO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
broken door striker
first problem is the hinge get worn or broken from being leaned on. second problem is the door gets slammed trying to close it braking the striker. to fix the problem 2 screws for the striker, to permanently fix repair door hinge. and a big thank you for the people who own and or run this site. my order was lost and they got the part to me the next day.
Parts Used:
Door Striker
  • james from egg harbor twp, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
plastic end of strike broken
I didn't have the right tool, so asked my handyman neighbor to come do a few projects and he had the driver in his pocket screw driver. it is a tip that is included in many multi-tip drivers. two screws removed the old and replaced the new. cheaper than local parts place, and no repair man. thanks
Parts Used:
Door Striker
  • Janet from Boise, ID
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
door strike broke while moving
very easy, just put in the 2 screws and it was fixed..
Parts Used:
Door Striker
  • Shari from Raleigh, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Would not go into spin cycle
Took off top. Removed 2 screws on Door Lock Assembly and replaced.
Parts Used:
Front Load Washer Door Lock and Switch Assembly
  • Jim from Dyersburg, TN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the FAFS4474LA0
91 - 105 of 165
Back to Top