This door lock and switch assembly is manufactured to lock the door on your front load washer to prevent it from opening while it is running. You may need to replace the door lock and switch if the do...
Also known as a Door Boot Seal and is used in front load washers. This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately f...
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
Ask our experts a question about this model and we'll get back to you as soon as possible!
7 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Nay
January 21, 2023
looking for stacking kit
For model number FAFS4272LW0
Hello Nay, thank you for getting in touch. The stacking kit for your model is part number PS3412264. Customer service is available 7 days a week if you require assistance placing an order. Thanks again for reaching out!
Hello Robert, thank you for contacting us. We would suggest taking a look at your water line first. Make sure it is connected correctly and not broken. Check the valve on the back of the machine to find out if it is leaking. Check it with the multimeter. If this does not help, you need to replace the water inlet valve, part number PS2349248. It allows the water to flow into the tub. We hope this sorts out your problem!
When it comes to replacement parts for front loader washer door specifically, can you find whole door replacements? Or just parts sold individually separate?
For model number FAFS4272LW0
Hi Jessica,
Glad to hear from you. For this washer, there is no door assembly. The parts are sold individually. If you know what parts on the door need repair, please resubmit your question with this information and we would be happy to assist you. We look forward to hearing from you!
Was this helpful?
Thank you for voting!
William
November 30, 2019
I’m trying to find the rubber gasket/seal that goes on the around the inside of the washing machine. Is that available?
For model number FAFS4272LW0
Hi William, this part is linked below. Thank you for your question and good luck with your repair!
Hi Ron,
Thank you for your question. The part number listed under your model number for the touchpad is PS3418963. We hope this helps. Thank you and have a great day.
1. Unplug unit. 2. Unscrew 2 nuts holding top in place in rear of unit using phillips head screwdriver. 3.Slide top back and remove. 4. Open door of washer and unscrew 2 screws holding in door lock unit. 5.Pull out unit from the top and install new unit reconnecting the 3 wire connections.
remove top of machine by removing 3 screws along the top edge in the back of your machine and then sliding the top back and up. Then loosen the screws holding on the control panel enough to get to the 2 screws at the top of the door panel. Next remove bottom panel by removing 2 screws along bottom edge then pulling it free from snaps. Then along the outside lip of the bellow, just inside the door, is a wire clip that is easily removed by prying it past rubber lip with a screw driver and lifting it away. Remove the door panel by removing the 2 screws you exposed by loosening the control panel and 2 more along the bottom that were exposed when removing bottom panel. After the door panel is removed and the bellow is completely exposed, you will find that it is held in place by a circular spring which wraps the whole way around the drum opening. Again it can be removed by prying it out away from the groove in which it sits with a screw driver. Now your machine is broken down as far as it needs to be. From here you can follow the directions included in your new bellow kit and put it back together by following these instructions in reverse.
Door lock takes a beating due to flimsy washer door which does not align well and subsequently gets slammed each time which causes lock to malfunction telling the washer that it is not locked. Due to safety the washer will not go into the spin mode. Remove top lid (2 screws) open washer door and loosed the 2 screws holding the lock assembly in place. Reach down into the washer and unsnap the 3 wire harnesses. Reverse to reinstall. Very easy.
