FAFS4272LR0 Frigidaire Washer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
door strike broke while moving
-
Shari from Raleigh, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Would not go into spin cycle
Took off top. Removed 2 screws on Door Lock Assembly and replaced.
Parts Used:
-
Jim from Dyersburg, TN
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Door lock mechanism broke and washer would not run
You must remove the top of the washer with screws on rear of washer. Top slides forward to remove. Once top is removed you can reach door lock mechanism from the top. Two screws must be removed from the front of the washer where lock enters mech. You can grab the mechanism from above by the wires that run to it. Undo wiring harness and insert new mehanism. Slide into place and attach in the front of washer with screws. This job is easy and can save you a lot on repair bills!
Parts Used:
-
SCOTT from SALINE, MI
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Front load washer would not spin
First we took the pump off and it was full so we hoped replacing it as the fan blades were broke and it didn't help. We replaced the control board and that didn't change it either. So I checked here and the door strike and door switch could be the problem so I ordered and put them on that was the problem. Thanks so much. Instructions were well printed and the job was about 5 minutes to replace. The washer works perfectly. We should have started with these parts first and it may not have cost so much.
Parts Used:
-
Regina from Milton, WV
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Washer would not go into spin cycle
1. Remove the spring clamp around the tub seal. 2. Pull back the tub seal in the area by the door lock switch. 3. Remove the switch assembly by removing two Phillips screws. 4. Remove connectors from switch. 5. Install connectors onto new switch. 6. Mount new switch on washer with two Phillips screws. Reinstall tub seal making sure to tuck it correctly on the washer frame. 7. Reinstall spring clamp.
Parts Used:
-
Brian from Brillion, WI
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Error Code E43 - door lock problem - no spin
Removed retaining band around door boot and prized-off boot on left side to access door lock - simple screw driver replacement job. Deleted last error code. BUT - washer worked again for several days, and now code E43 is back and won't spin - problem is intermittent - so suspect it is NOT the door lock, but a wiring or control board problem. Ongoing.
Parts Used:
-
Allan from Charlestown, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Door Strike broke
Take a deep breath and say, "I can do this. I will not pay well over $100 for someone else to come and do it."! Identifying part easy, mail very quick, web instructions clear, took out two screws, slipped out old part, put in new one, replace screws. I loved every minute of it and it cost $16.20 (part and shipping). Thanks, Part Select!
Parts Used:
-
Gillian from New York, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Washer would drain, but not spin
Removed two screws on the back of the washer top to release the top on the washer. Slid the top off and removed it. Opened washer door and removed two screws securing the door lock assembly to the washer frame. Reached in from the top of the washer to get the door lock assembly. Unplugged the old door lock assembly in three places and plugged the new assembly in in the same three places. Placed the new assembly in the same place as the old one and secured it to the washer frame with the same two screws located on the inside of the door. Replaced washer top and secured two screws at the top back edge of the washer... Tried the spin mode and everything worked great!!!
Parts Used:
-
Tom from Atascadero, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Plastic on door broke.
-
edward from ottawa, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Door would not close
The latch that held the door broke off, and of course the washer would not work , I called around locally and the small part price was outrageous,I went on line and found Pats select,and the price of the part was 1/3 of the cost locally I order the part and even with next day delivery I saved money from buying it locally
Parts Used:
-
Deborah from Keeling, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Door would not close. Washer would not turn on
-
Larry from Newhall, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Door latch broke
-
ANDREW from UPLAND, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
machine would not cycle and would not drain
I read other problems, I jumped the gun and purchased the door switch, this was easy to change, but MY machine still had the same issues, however, I found that the filter was plugged, and after I cleaned this out, this fixed my issues and the machine works fine, So I now have a door switch and striker should mine go bad, Hope this helps out
Parts Used:
-
Jeffrey from Cedar Rapids, IA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
plastic piece broke from door strike keeping door from closing and therefore the washer wouldn't work.
Ordered a replacement door strike which was easily replaced with Phillips screwdriver. I was very grateful that the part was so easy to find on this website. It was helpful that I had saved my book with model number of washer which allowed me to find the exact part needed. Thanks!!!!
Parts Used:
-
Rebecca from Frisco, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Broken Door Striker
Removed two phillips screws. Removed old door striker. Replaced with new door striker. Replaced old phillips screws. Job takes less than 1 minute.
Parts Used:
-
Robert from Hyattsville, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!