F32C546CS1 Frigidaire Dryer - Instructions

Open the top cover by pushing the retention clips in from the front (just under the top edge) with the putty knife - that was the hardest to figure out - I found it online.
The rest is just 4 screws - 2 inside to release the plastic filter holder and two on the inner edges of the front panel.
Took the front off, ripped the old slider, cleaned the glue residue with alcohol and mineral spirits and a lot of scrubbing, vacuumed all the lint from the fan.
Then glued the new slider in place and clamped it together. Didnt know how long the glue takes so I left it overnight, just in case.
It works well now. Cleaning the ducts and the fan with the vacuum hose made a world of an efficiency difference. They should make an easy way to do this for regular maintenance!

I First pulled the top panel up and off from the front. Then, on the inside, removed a square head screw from each side holding the front door panel on. I then pulled off the front panel enough to expose the drum. I then removed the old drum glide with a putty knife, and following instructions supplied with the new glide, glued the new glide into place. I then assembled in reverse order of disassembly.

First I raised the top of dryer, then removed 2 screws holding the front of dryer to the sides. removed old drum glide using a putty knife and glued new glide in place with glue provided. replaced front and top. The whole job took about 20 minuets and saved me the cost of new dryer

Removed back panel. Popped off top of dryer, then removed front of dryer. Slid belt onto tumbler, put front cover back on, put top back on and adjusted belt frombottom panel cover.

There was a gap between the drum and the front opening. So, we opened the top of the dryer using the putty knife. There are two clips once you find them you just have to push back on them to release the top of the dryer. Then there are two screws that hold the front of the dryer on. Once they are removed the front of the dryer just came off. The kit has glue and instructions past that point and I just followed them.

First I removed power from dryer. Then I lifted the lid and removed the 2 screws holding the front onto the dryer. I then used a pair of pliers to grip the seal and help pull it off. Cleaned off old adhesive. Recommend getting GOOP BE GONE. Then apply high temp sealant onto area and place seal on top. Press firmly across it to make sure it is in place. Then put it all back together and your done. Also, if upper seal is worn.recommend ordering lower seal at same time. I didn't and should have. Save yourself from doing this twice.

I know that the knobs on the Gibson dryers break as they are plastic and the back cracks so it won't turn. I have had to get several new ones over the years. I went to Google put in Gibson dryer knob and found it, I had the model number so that helped. I had the part within 24 hrs, awesome service from PartSelect.
Emma W

Opened top of dryer with screw driver,removed two screws securing the front door. moved door away from dryer. Removed old felt from door,scraped area to remove old glue and felt. Lightly sanded area to clean. Applied new provided glue and let set for 1 minute. put new felt in place and applied three small clamps to hold in place. Waited 1 hour and reassembled dryer.

Opened the plastic bag, took out the new knob, slid it on and DONE I'm not using pliers anymore!!

/removed the lint screen & tossed in the trash, removed one screw from each side of the frame with a screw driver. Placed the New frame in place
& secured it with the screws that I removed from the old frame, placed the screen in place & that was all there was to it. The total amount of time to remove the old & replace with the new probably took 10-15 min. @ the most. I am so happy to have found the part & was able to replace it. You all are wonderful. Received it in 3 days, WOW!!

The first thing I did was logged onto the internet to search the web for my dryer information. Next, after I found the correct model, the site referred me to the parts section and that is where I determined the problem was the M series ignition coil. I then unplugged the dryer and turned off the gas. I took a screwdriver and popped the top off and cut the wire straps that held the door strips and the light to the front panel. I then unplugged the door switch at the connector - HOWEVER - DO NOT TRY TO REMOVE THE WIRES FROM THE ACTUAL DOOR SWITCH BECAUSE THEY ARE VERY FRAGILE AND CAN EASILY BREAK. Next, I removed the two screws that hold the front panel on. By using a slight bit of pressure, I removed the front panel and was able to locate where the ignition coil switch was. (It was right in front) I then removed the two screws that held the clamp down, as well as the bad coils. The coils easily slid off the post and the new pieces slid back on just as easy. I then replaced the screws and clamps to hold the new pieces in place and replaced the front panel. **NOTE ~ while the front panel is off, it would be a good time to clean out all the built up dirt and lint that has accumulated over the years. Lastly, I re-connected all switches and wires and replaced the top panel. Once I turned the gas back on, everything ran beautifully.

Removed rear cover, unplug 2 spade connectors, twist out old switch, twistin new switch. plug connectors, install cover

Sooooo Easy. A no brainer. Just line up the knob and push it back on!

Pushed the new timer knob on the dryer. No tools were necessary.

I unpluged the dryer, raised the top cover up, removed 2 two screws & pulled front cover out. Removed the old seal, cleaned the area & installed the new seal. Reinstalled as new. Very, very easy.