F101 Jenn-Air Range - Instructions

Locate and open appropriate breaker to kill power to the range. (very important if you intend to see tomorrow).

Pull off the control knob.

Remove 2 screws that hold in control pannel.

Lift out the control pannel to the extent that the wires will let you. (2-3 inches)

Remove the nut that holds the switch/controller in the pannel.

Remove the wires one at a time and reconnect them to the new switch. Make sure to connect them the same way on the new switch.

Re-install the switch in the pannel.

Re-install the pannel in the stove.

Close breaker and test burner contol.

Took the old knobs off and replaced them with the new!

Our oven is at least 30 years old and the parts are not even available through the manufacture anymore. A new stove would cost well over $1000.00. Jen airr is the only down draft stove available. So the repair was much more affordable that the alturnative. So thank you to part select for providing this service. The repair was simple. This is coming from a 36 year old female who has been around electrical work, but never done any myself. My husband was out of town and I felt I could do the job. I first made sure I had another adult present. I turned off the power to the oven. I then removed the visible screws to the element plate (2 on top and 1 in lower middle). I then pulled the element out enough to get behind the plate and feel the screws that were connecting the wires to the element/ground. Again 3 total. The oven space is very small and difficult to work in. I had to do a lot by feel. Once the old element was free I just exchanged it for the new one and reversed the process, making sure all the wires were tight. I then turned the power back on. Turned the oven on, it smoked lightly for a moment and turned red hot. Over all it was extreemly simple.

I removed the two screws that held the electrical
switch control. Then I raised the control upward an tilted it sideways an jumped the two terminals with a screwdriver. then i knew the switch was bad. So then i removed the two pail nuts that held the switch to the switch control an removed the old switch. Then installed the new switch in the reverse proscess. This was fairly easy

It's wonderful to get accessories for this 20 year old Jenn-Air. I love it and now it looks like new.

Remove and replace with new. No tools required.

This is fantastic. We've had this Jenn-Air range for some time now, but we only used the two-burner module on one side and the indoor grill on the other. Less than a week before Thanksgiving we decided that the extra two burners would be very useful, so I set out to search the internet for a good deal and the possibility of getting it before needed. Then I found your website and within minutes theunit was on the way and, at the most reasonalable price available. I recieved the unit he next day. All I had to do was plug in the module and it was done.
Thanks for making life easy

Unplug old burner assembly and plug in new one

pull out the grille element and replace with cooking element

Each cartridge unit consists of two electric coil burners in a larger frame assembly. The old cartridge units simply lift up and unplug from the range top. The new units simply plug in and drop into place. It probably took more time to unpack the box than to remove the old, and insert the new cartridges. Anyone can make this repair, which instantly converts an old range top into a new one.

Pulled out old element and inserted new one (approx. one min.)

After searching on the internet for a very long time, we were almost ready to order the screws "blind" (no picture) from Sears for almost $10.oo per screw. Then I stumbled onto this website and found exactly what I was looking for, with a detailed description AND a picture!! Not to mention a price that was two thirds less than Sears..for TWO screws. Now the oven door is secure and we are no longer on our search for the right screws.

Purchased 2 piece broiler pan from this site

After discovering that the Jenn-Air cartridges unplugged from the stove, it could not have been more simple to order a new one from PartSelect (it arrived in two days), unplug the old cartridge, and plug in the new one - and no tools required!

following the directions in the package and on-line, this repair was easier than i could have imagined. changing out these two parts took less than 15 minutes.