ETS22XBPBRWW General Electric Refrigerator - Instructions

I opened freezer and removed Ice maker. Then removed top fan hood and finally the freezer back panel. Unplug fridge.Removed fan bracket and swapped gromet and fand blade to new motor. Put back in fan bracket and reassembled.Note: Tried without putting back together to see if the fan worked and it won't. Must plug all connections in including ice maker for fan to function. Fixed problem and fridge is better than it ever was. Part Select was excellent,Fast shipping! Thanks

The hard part was cleaning the dust around the coil and fan area. Its plug and play right after that. Two nuts on the fan housing and a wire harness snaps on and off. Bam! 1,2,3 Up and running. . Like new. . . Thank you ps

removed ice maker, back panel and two additional plastic trim pices to get to fan. Single molex connection for the wires. I got the part the next day. Wasn't expecting part for three to five days. Very impressed!

Replaced defrost thermostat along with temp sensor watched the video on this page simple fix

I used pliers to pull lightly on the head of the switch, while I inserted a small flat head screw driver into the base of switch and gently worked around the edges to free it from the panel.

Removed the broken slide (two screws) replaced with the new part

Raised side of fridge enough to get 1/4" ratchet with 1/4" socket under roller wheel assy. Removed three hex-head screws to separate damaged wheel assy from fridge frame. From panel below fridge compartment, backed-out stripped leveling screw. Mounted new roller assy and then threaded in new leveling screw from front. Lowered fridge and adjusted leveling screw for proper height. Suggest putting a 2x4 under fridge for safety when hands are under unit.

First I removed the left condensor fan motor bracket nut, loosened the right motor bracket, dropped the moter bracket down freeing the motor from the rubber grommets.
Pulled the fan off from the motor shaft, pressed the new fan on the shaft and installed new grommets. Replaced the motor bracket and tightened the right bracket nut and checked fan for clearance and free spin. Reinstaled the left bracket nut. Turned on the refrigerator and checked fan for action. Everything worked great.
I did not know the fan replacement came with a compression ring already installed, so now I have an extra compression ring.

In freezer box removed shelf, removed 2 screws from back panel, removed 3 plastic covers (1 with 2 screws, other 2 snaped out. Unsnaped defrost thermostat from copper tube then cut 2 wires (yellow & orange) stripped all wires back a little then used 2 wire nuts to reconnect the new thermostat and resnapped back onto the copper tube. Removed 4 screws from evaporator fan housing (original one warped from overheat and caused fan blade to get chewed up) unpluged fan motor wiring and removed ground wire and motor from warped housing, removed fan plade by just pulling on it. Installed new fan blade by pushing it on the fan motor shaft, reinstalled the fan to the housing and the housing into the freezer box. In the frig box I removed the control panel from top of the box by removing 4 screws and unpluging the main wiring plug and the defroster control then reinstalled it all in reverse order. Also had to renew the stick on foam on the evap fan housing. Over all it was an easy task.

I read stories from the website how others did it so I figured I would give it a try. I put all the frozen stuff in the refrigerator piled up. Took out the shelves. Took out 2 screws with a socket extension ( nut driver will work fine.) Remove the light bulb. lifted up on the back panel...it came right out. Saw the coils and on top the sensor. Took it off, cut the wires, spliced in the color coded new one ( pink to pink, orange to orange) Stuck it in the top coil in the original position and crossed my fingers! I put all the pieces back easily, restocked the freezer and waited. HOORAY!! My ice cubes are all separate and free. NO frost inside. A very easy fix for $20.

Note: If there is a large amount of ice build up on your coils a hair dryer works great. The drain is on the bottom anyway. Also , you may want to seal around the wire nuts to keep moisture out. I did

diagram from part select matched my fridge perfect. i ordered all parts that involve defrosting coils. ( defrost heater 618, defrost thermostat 620, defrost thermostat 627 ). two wires involved with thermostat, just removed all old parts and replaced with new. Part Select videos helped demonstrate the projects well.

Like the other repair story I read about this part, the fridge was cool not cold (58* instead of an ideal 38*), and my ice cream stayed soft in the freezer. I removed the pannels in the freezer with a small socket wrench to find the fan burnt out. When the motor came, all I had to do was move the fan blade and gromets to the new motor. Closed it into the brackets and remounted it to the freezer. The part cost less here than at the factory web site and the fridge works great. Thank you PartSelect.com!

used prior reviews, was good, I was not sure how to remove fan blade. It just pulls off.
space is tight but every thing went ok.

The old switch was hard to remove. Thinking that I may have to loosen the wires I used a socket wrench to remove a clamp. This was unnecessary. In the end the switch did come out using a large size screwdriver. The problem was that the expanding plastic tongue is not visible from the ouside so you have to try to feel your way around. If i had ordered the replacement before and not afterwards I would have seen this before hand.

After replacing the light bulb and still no light I manually pushed the light switch button. Intermittently the light would come on then go out. I removed the power plug from the power source then replaced the light switch. I plugged the refrigerator back in and now I open the door the light comes on and stays on until the door is closed.