This 3-coil 5500 watts heating element with housing is used to produce heat to dry the clothes in your dryer. The heating element is strung with a coiled wired. The wire receives, but resists a contro...
This high limit thermostat has a limit of 260 degrees Fahrenheit. Meaning that it will cut out when the internal dryer temperature reaches 260. This thermostat cuts back in when the temperature drops ...
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
This is a genuine OEM lint filter, which works with dryers.
$174.99
In Stock
Questions And Answers for EIMED60LT3
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Laurie
June 24, 2022
Error code E64
For model number EIMED60LT3
Hello Laurie, thank you for your inquiry. Error Code 64 means the dryer is sensing there is a problem with the Heating Element PS2349309 . It could be that a coil has broken, the element has a short circuit, or a wire is defective.
Door glass of dryer is scratched, is there a replacement?
For model number EIMED60LT3
Hi Megan, thank you for the question. Yes, the outer door window of your model is part number PS2349411, and the inner door glass is part number PS8691870. If you need help placing an order, customer service is open 7 days a week!
We have E64. Dryer runs until it gets really hot then shuts off…about 5 min first time then less and less unless we let it cool completely then start over.
For model number EIMED60LT3
Hi Cheryl, Thank you for reaching out. The E64 error code indicates a problem with the dryer's heating. This could be due to a faulty heating element, thermal fuse, cycling thermostat, or airflow with the lint filter, duct and vent system. We hope this helps!
When I described the noise to a YouTube appliance diagnostician, I was directed to check the felt seals front and back of the rotating drum for wear, tears, or foreign objects. As it happens the felt seals looked find and there were foreign objects so, not wanting to disassemble and reassemble the dryer more than I had, I ended up replacing all the replaceable moving parts that I considered possible culprits: The idler tension spring, the idler tension bracket (which includes a nylon pulley wheel), the drum belt, the five rubber-tipped bearings that support the drum and keep it in place, and the foam seal on the blower housing which seemed a little brittle and old, as well as high-temperature adhesive for the latter. The instructional videos here and on YouTube were extremely helpful (I doubt that I would have attempted this job at all, had I not watched these ahead of time). The most time-consuming aspect was waiting for the arrival of the parts as I didn't order them all at the same time or all from the same place (I ordered from whomever could ship me a given part the fastest. Disassembly took less than an hour. Re-assembly with the new parts in place took about the same but was a little more awkward because this appliance sits in a very narrow closet and it's difficult to ensure that the 4" flexible duct stays in place when sliding the appliance back into the closet. No regrets. Now I know the basics if this dryer needs attention in future and I also know all the parts that I can eliminate as suspects in any future maintenance (the parts that I replaced)
Removed back of dryer with electric nut driver. Lots of screws. Removed old heating element to better access wires and thermostats. Removed baffle at end and transferred to new heater element. Transferred thermostats to new element, reconnected wiring in correct order. Installed new heater element in correct position using tab to locate. Replaced back of dryer. Reconnected dryer vent. Toughest part was squeezing out of space after reconnecting dryer vent. Unfortunately, too short for my weight.
1. Loosened the 3 screws inside of the drum 2. Removed the entire back of the dryer (lots of screws) 3. Removed the old vent (there are 2 screws at the bottom that hold it in) 4. Install new vent (put the screws back in) 5. Close up back and proceed to put all of the screws back
