If your dryer drum has stopped spinning and your clothes are coming out damp, it might be time to replace the belt. This essential part helps the drum rotate, allowing warm air to circulate and dry yo...
This 3-coil 5500 watts heating element with housing is used to produce heat to dry the clothes in your dryer. The heating element is strung with a coiled wired. The wire receives, but resists a contro...
This high limit thermostat has a limit of 260 degrees Fahrenheit. Meaning that it will cut out when the internal dryer temperature reaches 260. This thermostat cuts back in when the temperature drops ...
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
This gray lint filter is used to collect lint and debris as it passes through the dryer vent. It is recommended to clean the lint filter before every load to clear the air flow through the lint filter...
This replacement drum support roller helps keep your dryer drum turning smoothly and quietly during operation. Designed for reliable performance, it supports the drum as it rotates to help reduce exce...
This moisture sensor assembly ensures your dryer delivers optimal performance by detecting the moisture level in each load. By accurately measuring dampness, it allows the appliance to adjust cycle ti...
This dryer thermal fuse is a critical safety component designed to protect the appliance from overheating. It automatically shuts off power to the motor or heating system if excessive temperatures are...
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Hary
October 11, 2023
Says “door open” even when closed. Part # for the switch is 511122M. Seems to be discontinued. Is there a substitute part?
For model number EIMED60JIW0
Hello Hary, thank you for reaching out. Sadly, we do not have any information on the part number you provided for the switch. However, the compatible door switch for your model is part number PS2330879. If you need help placing an order, customer service is open 7 days a week!
Dryer does not start due to door not close even though door is closed
For model number EIMED60JIW0
Hello Jackie, thank you for reaching out to us. A dryer that won't start because it thinks the door is open, despite being closed, is likely caused by a faulty door switch. You may need to replace the door switch, part number PS2367765, to fix the issue. We hope this information helps!
Removed back of dryer with electric nut driver. Lots of screws. Removed old heating element to better access wires and thermostats. Removed baffle at end and transferred to new heater element. Transferred thermostats to new element, reconnected wiring in correct order. Installed new heater element in correct position using tab to locate. Replaced back of dryer. Reconnected dryer vent. Toughest part was squeezing out of space after reconnecting dryer vent. Unfortunately, too short for my weight.
1. Loosened the 3 screws inside of the drum 2. Removed the entire back of the dryer (lots of screws) 3. Removed the old vent (there are 2 screws at the bottom that hold it in) 4. Install new vent (put the screws back in) 5. Close up back and proceed to put all of the screws back
The ice maker wouldn't fill with water. The maker itself appeared to operate but the tray would not fill. I ordered the part from PartSelect.com. The website allowed me to conveniently match a picture of the part with my part on the refrig. I ordered the part and it arrived in two days. I was impressed!
I turned the water to the ice maker off, unplugged the refrig. and pulled it out from the wall. I loosened and removed two screws with a nut-driver and unplug the wiring connection from the old part by simply pulling on it with my fingers. I then unscrewed the water connection from the old part using a set of pliers. The old part was then discarded. I connected the water and electrical and remounted the new part using the two screws. It was too easy!
