EILFU21GS1 Electrolux Freezer - Instructions

Unplug freezer let stand all night to defrost. Remove the tray cover which is located on the upper back area inside the freezer.( 3 twist fittings remove it ). Remove the upper stainless steel panel which is secured with 6 screws. This will drop down exposing the condenser. Note all the wires and fan will stay attached to the stainless steel panel, this panel will drop down no need to unplug anything. On the left upper side next to the condenser you will see the thermostat. Two color coded wires. Remove the thermostat and install the new one at the same location.

Installed new fill valve in less than 30 minutes and waited for 24-8 hours for results to no avail. Ice maker mechanism was shot and still would not work. Went to Lowes and bought entire ice maker add on kit for my model ice box and installed in 30 minutes and have been making ice ever since. Your 99% cure rate was 100% incorrect. Save the time and effort and go to a big box store and just get a new ice maker. By the way, it only costs about $20 more to do that.

ice maker= replaced overload,microswitch and solenoid water valves.refrigerator=replaced the thermostat.Great price on parts,very fast delivery and parts were a perfect fit.You made the job very easy. John

Replaced fan. I ordered the fan and received it the following.(-:

Unplugged freezer from electrical socket. Removed lower trays from freezer. Removed sound proof stripping from sides of back panel. Removed upper, lower and side screws from back, lower panel using No. 2 phillips screwdriver. Disconnected motor wires from quick disconnect power supply. Removed motor bracket from freezer back using nut driver. Removed motor from bracket using same nut driver. Replaced motor and screws in bracket. reattached quick disconnect. Attached fan blade to motor making certain to push blade on shaft securely. Replaced bracket to freezer back. Replaced back cover. Replaced stripping. Plugged into power supply. Total time 15-20 minutes.

Followed the sites instructions. Empty the bottom part of the freezer. Remove the screws. Move the panel out of the way. Easily remove the old part and replace with the new. Put the panel and screws back in place. The freezer works.

per the video..easy installation....unfortunately the temperature did not improve. We still have a refrigerator temp in the upper freezer.....and a "cooler" in the refrigerator section

Remove the cover panel inside the freezer, remove and replace the fan motor (pull fan blades off old motor and push on the new one) and replace the cover.

Pulled freezer out from where located to allow shelves to be removed.Unplugged unit, removed shelves and evaporator cover, installed new fan motor. Plugged unit up to check fan motor operation. Reassembled unit, installed shelves and moved freezer back into original location.

TURN OFF WATER!! UNPLUG REFRIGERATOR!! Remove water fittings and electrical connector on old valve. Remove two mounting screws on pump bracket. Reverse procedure to install.

Took out three shelves. Removed 9 screws with a battery powered drill with a phillip screwdriver bit. Popped off the thermostat like I had seen on the video. Put the new thermostat on. Replaced the two wires one at a time. Reassembled the unit. This was so quick that my wife told me to let her know when I wanted to fix the freezer. She was shocked that I had completed the job. I'd been in the garage less than 10 minutes. It has been six weeks. and the freezer is working perfectly.

Remove back cover (5 screws )remove valve ( 1 screw ).Disconnect in and out water lines. Disconnect wire on solenoid. Install in reverse. Dont forget to turn off water.

The sliding shelf side rail is held by three philips head screws that tighten into nut inserts. No amount of tightening would keep two of the three screws tight. I found that the nut inserts which are plastic and insert into the side of the freezer would pull loose, probably from years of overloading the sliding shelf basket. Ordered two nut inserts from PartSelect. 1. Remove three screws to remove shelf slide side rail. 2. Remove nut inserts to be replaced with needle nose pliers or reinsert screw a couple of turns and pull nut insert out with pliers. 3. Insert new nut inserts, position side rail, and tighten screws. Replace sliding shelf/basket.

The two screws that held the ice maker in place could not be seen do to there location. I could only get one hand inside do to space restriction.So I placed a mirror inside so I could see the screw heads and from point it was very easy to see and line up the nut driver on the screw heads. I then lifted it up and unplugged the wiring and installed the new ice maker. Works like a charm. Paul

Watched video on Part Select which shows you how to replace the thermostat with several good pointers. Very easily done and now the freezer works great.