This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
Ask our experts a question about this model and we'll get back to you as soon as possible!
14 questions answered by our experts.
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Fred
December 16, 2022
Hi! My washing machine evacuate the water very slowly. Hard time draining. It's showing me E21 on the screen. Can someone help me please!
For model number EIFLS60LT1
Hello Fred, thank you for your inquiry. The E21 means that the water in your washing machine is not pumping out fast enough. First, check the drain hose for any restrictions or kinks. If the drain hose appears to be clear and free, then the issue is with the Drain Pump, part number PS3655041. If you require assistance to place an order, please contact customer service. We hope that helps!
Cold water run all the time even when the washer not running
For model number EIFLS60LT1
Hello AHMED and thanks for writing.
It sounds like a faulty water inlet valve PS2349248 check and replace if needed. We hope this helps. Please contact us anytime.
When the washer is on spin cycle it makes a loud banging sound in sync with the rotation of the tub
For model number EIFLS60LT1
Hello Gary and thank you for writing.
If the shock absorbers PS8689636 in your front loader becomes weak the washer will make a loud banging sound during the spinning cycle. We hope this helps. Please contact us anytime if you require further assistance.
I asked about a banging sound on spin cycle for an Electrolux washer model eifls60lt1. You responded that the shock absorbers was likely issue and recommended shock absorber kit ps8689636 @ $145.85. There is another kit for this washer model ps8689635 @ $45.39. Can you advise the difference in the kits? And, the schematic for the kit ps8689636, shows a Frigidaire washer. I just want to verify that these parts work for Electrolux. Thanks for your help with these questions.
For model number EIFLS60LT1
Hello Gary and thank you for writing.
So after lengthy research this is the answer:
1. Frigidaire and Electrolux share parts, so this is not a problem.
2. Your model requires 2 front absorbers PS8689636 and 2 back absorbers PS8689635.
3. The front absorbers are much more expensive. Usually, the front absorbers are the first to be faulty, that is why this kit was recommended in the first place. We hope this explanation helps. Please contact us anytime if you require further assistance.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Leticia
July 19, 2022
My washer doesn’t spin
For model number EIFLS60LT1
Hello Leticia, Thank you for your inquiry. We have researched the model you have provided and we would recommend checking the following parts to fix your issue: the belt, the idler pulley, the drive motor, the motor control board and the door latch assembly. You can test the latch and motor with a multimeter, and check the other parts for any visible damage. We hope this helps and if you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
Bought new part. #1 Lesson learned: Always inspect the actual part number of the ordered/received part. Verify with number marked on the item somewhere. We did not do this and turned out we reinstalled a slightly smaller bellow (wrong part number received in shipment). We were able to fully install it but it was minutely not laying perfectly around the diameter. So minor we did not notice. We did have great difficulty installing though. Anyway, after 1st test run, bellow already had developed a small hole in bottom right quadrant from rubbing on the drum. Left a bunch of gray powdery debris on the drum too. We did not realize error until that point. Took bellow off again to verify part number on it. It was wrong. That explained why the door was so very tight to close and difficult to open. Other than all that, use the video to do the install. It was free to view and easy to follow.
First, I went to the PartSelect website and easily found the part at a reasonable price. I ordered it early on a Wednesday afternoon, and gladly spent the extra $25 to ship it overnight. That evening, PartSelect sent me an email stating that the part had shipped that very day, and - mistakenly - I took that literally. FedEx tracking predicted that the part would arrive on Friday, July 5, which made sense because the 4th was a holiday. But I found out that the part had actually shipped on the 3rd, as the email had informed me. It didn't actually ship until the 4th - up until then, a "shipping label" had been created but it had not shipped. FedEx then revised their arrival date to Monday, 8 July. That clearly wasn't satisfactory. So I went to my local parts distributor, Dayton Appliance Parts, a fifteen-minute drive from my house, and got the same part for $3 cheaper, plus without the $25 shipping fee that PartSelect had charged me for overnight-shipping-that-isn't-actually-overnight-shipping. Once I had the part in hand, installation was a breeze. Two screws removed, pulled the striker, replaced the new part and the screws. Less than two minutes. But no thanks to PartSelect.
Parts took twice as long to arrive shipped from Utah to Houston, Texas. Once arrived parts were straight forward to install. 1) Open the door by tripping the door strike using yard trimmer line. 2) Turned Power off (unplugged unit) 3) Used needle noses pliers to remove door rubber boot retainer 4) Folded right-side of rubber in to removed switch assembly 5) Used Phillips screwdriver to remove switch assembly screws, navigated damaged switch part forward then disconnected line. 6) Connected new switch to line, navigate part back into washer and screwed back in. 7) Repositioned door rubber boot and reattached door boot retainer wire with hands and needle noose pliers. 8) Replaced door strike using Phillips screw driver. 9) Re-plugged washer power to outlet, closed door and ran a test cycle. All good!
