This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
$16.47
In Stock
Order within the next 4 hrs and your part ships today!
Order within the next 4 hrs and your part ships today!
Questions And Answers for EIFLS60JIW1
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Huguette
March 11, 2023
Accidentally bumped my half open soap dispenser, it fell on floor and the front part with the button you push to open the door when adding soap disconnected from remainder of drawer. Put things back together BUT can’t snap the front part with the push button to open the door back properly. Can snap bottom but top part remains loose and comes off.
For model number EIFLS60JIW1
Hello Huguette, thank you for your question. Sadly, the front part cannot be purchased separately. It is sold as the Dispenser Drawer Assembly part PS3495314. Thank you and have a great day.
1 person found this helpful.
Was this helpful?
Thank you for voting!
David
May 11, 2022
My Electrolux washer does not start. I have tried:10 minute breaker power off reset
door opens, closes and latches also tried holding it closed while pushing start
control panel lights up and is functional except start button
tub turns,
delay is off set at 0.00
control lock is off
water is on
when start is pushed, either does nothing or beeps and goes dark.
can you help?
For model number EIFLS60JIW1
Hi David,
Thank you for your question. If your washer will not start, there are some parts that you will need to check to see which one is causing the issue. You will need to check the door lock and switch assembly, the door strike, the drive motor and the electronic control board. We have included a link that you may reference on how to check these parts. Once you have determined the part you need, please feel free to call customer service. We are open 7 days a week and anyone will be happy to assist you. We look forward to hearing from you!
Removed old drawer and replaced it with new one. This is the second drawer assembly I have purchased in 6 months. This piece of junk must be a cash cow for Electrolux. If they would make the small latch out of metal instead of plastic, there would be no problem. But that might cost an additional $ .007 per washer. On the positive side, partselect.com had the part and delivered it promptly.
Bought new part. #1 Lesson learned: Always inspect the actual part number of the ordered/received part. Verify with number marked on the item somewhere. We did not do this and turned out we reinstalled a slightly smaller bellow (wrong part number received in shipment). We were able to fully install it but it was minutely not laying perfectly around the diameter. So minor we did not notice. We did have great difficulty installing though. Anyway, after 1st test run, bellow already had developed a small hole in bottom right quadrant from rubbing on the drum. Left a bunch of gray powdery debris on the drum too. We did not realize error until that point. Took bellow off again to verify part number on it. It was wrong. That explained why the door was so very tight to close and difficult to open. Other than all that, use the video to do the install. It was free to view and easy to follow.
First, I went to the PartSelect website and easily found the part at a reasonable price. I ordered it early on a Wednesday afternoon, and gladly spent the extra $25 to ship it overnight. That evening, PartSelect sent me an email stating that the part had shipped that very day, and - mistakenly - I took that literally. FedEx tracking predicted that the part would arrive on Friday, July 5, which made sense because the 4th was a holiday. But I found out that the part had actually shipped on the 3rd, as the email had informed me. It didn't actually ship until the 4th - up until then, a "shipping label" had been created but it had not shipped. FedEx then revised their arrival date to Monday, 8 July. That clearly wasn't satisfactory. So I went to my local parts distributor, Dayton Appliance Parts, a fifteen-minute drive from my house, and got the same part for $3 cheaper, plus without the $25 shipping fee that PartSelect had charged me for overnight-shipping-that-isn't-actually-overnight-shipping. Once I had the part in hand, installation was a breeze. Two screws removed, pulled the striker, replaced the new part and the screws. Less than two minutes. But no thanks to PartSelect.
