If your dryer drum has stopped spinning and your clothes are coming out damp, it might be time to replace the belt. This essential part helps the drum rotate, allowing warm air to circulate and dry yo...
$84.00
In Stock
Order within the next 4 hrs and your part ships today!
This high limit thermostat has a limit of 260 degrees Fahrenheit. Meaning that it will cut out when the internal dryer temperature reaches 260. This thermostat cuts back in when the temperature drops ...
$68.15
In Stock
Order within the next 4 hrs and your part ships today!
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
$28.95
In Stock
Order within the next 4 hrs and your part ships today!
Need a way to keep your dryer safe and protected from overheating? Then the Frigidaire Thermal Limiter is your perfect go-to solution. This genuine part acts as a guard, automatically shutting off you...
$41.75
In Stock
Order within the next 4 hrs and your part ships today!
This genuine OEM dryer drum roller wheel assembly is designed to support the dryer drum and allow it to rotate smoothly and quietly during operation. A properly functioning roller helps keep the drum ...
$44.34
In Stock
Order within the next 4 hrs and your part ships today!
This dryer thermal fuse is a critical safety component designed to protect the appliance from overheating. It automatically shuts off power to the motor or heating system if excessive temperatures are...
$44.34
In Stock
Order within the next 4 hrs and your part ships today!
This element is strung with a coiled wire made of a nickel and a chrome alloy. This wire receives, but resists, a controlled electric current and as a result, the wire heats up. The heat produced is u...
$140.14
In Stock
Order within the next 4 hrs and your part ships today!
If your dryer drum isn’t spinning or the airflow seems off, the drive motor might need replacing. This motor comes with the pulley already attached for the drum belt and has reverse threads to hold th...
$328.62
In Stock
Order within the next 4 hrs and your part ships today!
Questions And Answers for EIED50LIW2
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Michael
September 12, 2022
i am getting an error code of "clean litler) lint filter appears clean . is there another filter or does this mean something else is wrong?
thanks
Mike
For model number EIED50LIW2
Hello Michael, thank you for contacting us. If the lint filter is clean and you are still seeing the clean filter error, it indicates some fault in the control board which is falsely sensing lint filter blockage. We hope this sorts out your problem!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
When I described the noise to a YouTube appliance diagnostician, I was directed to check the felt seals front and back of the rotating drum for wear, tears, or foreign objects. As it happens the felt seals looked find and there were foreign objects so, not wanting to disassemble and reassemble the dryer more than I had, I ended up replacing all the replaceable moving parts that I considered possible culprits: The idler tension spring, the idler tension bracket (which includes a nylon pulley wheel), the drum belt, the five rubber-tipped bearings that support the drum and keep it in place, and the foam seal on the blower housing which seemed a little brittle and old, as well as high-temperature adhesive for the latter. The instructional videos here and on YouTube were extremely helpful (I doubt that I would have attempted this job at all, had I not watched these ahead of time). The most time-consuming aspect was waiting for the arrival of the parts as I didn't order them all at the same time or all from the same place (I ordered from whomever could ship me a given part the fastest. Disassembly took less than an hour. Re-assembly with the new parts in place took about the same but was a little more awkward because this appliance sits in a very narrow closet and it's difficult to ensure that the 4" flexible duct stays in place when sliding the appliance back into the closet. No regrets. Now I know the basics if this dryer needs attention in future and I also know all the parts that I can eliminate as suspects in any future maintenance (the parts that I replaced)
1. Loosened the 3 screws inside of the drum 2. Removed the entire back of the dryer (lots of screws) 3. Removed the old vent (there are 2 screws at the bottom that hold it in) 4. Install new vent (put the screws back in) 5. Close up back and proceed to put all of the screws back
I removed the front, top and back panels of the dryer, installed belt around drum and through the pulley system so the belt was snug, replaced all screws and panels, and done.
