This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Don
October 30, 2023
My washing machine shuts off during hot water wash. It works fine with cold water
For model number EFLS627UTT0
Hi Don, thank you for reaching out. We have found that the issue is with the water inlet valve, part number PS16544354. We would recommend checking the inlet valve to fix the issue. Good luck with your repair!
Sometimes the machine somehow catches and snags clothes
What would cause this?
For model number EFLS627UTT0
Hi Bill, thank you for reaching out. Based on our understanding, we would recommend checking the drum baffle, part number PS3418909. It lifts and tumbles the clothes inside the spin basket. You may need to replace it to fix the issue. We hope that helps!
The front keeps coming of the soap dispenser drawer. How do I replace or fix it?
For model number EFLS627UTT0
Hi James, thank you for reaching out. If the front drawer handle of the dispenser keeps coming off, it might be defective and needs to be replaced. The part number for the compatible front drawer handle is PS12365887. If you require assistance to place an order, please contact customer service. We hope that helps!
My washer doesn't empty the fabric softener compartment. What is the correct part I need to replace? Ive read to replace the water intake valve but Im not sure what the part number is. Can You help me please?
For model number EFLS627UTT0
Hi Kim,
Thank you for your question. If fabric softener is not draining into the tub from the dispenser, you may need to give the dispenser a good cleaning as fabric softener and soap residue can build up over time. Refer to your owner's manual for the proper procedure on how to clean the dispenser. If water is not filling the fabric softener compartment, then the water inlet valve may not be working correctly and you will need to test it with a multimeter. Set your multimeter to Rx1 and touch the probes to the terminals. The reading of a functional valve varies from model to model, refer to your owner’s manual to determine what your reading should be. If you do not receive the recommended reading, you will need a replacement water inlet valve. The part number listed under your model number for the water inlet valve is PS16544354. If you would like to place an order for it, please call our customer service line and anyone will be happy to assist you. We look forward to hearing from you!
I have an Electrolux washer model number MODEL- EFLS627UTTO SERIAL- 4C91400773. I’m having problems with an error code E11. No water enter the tub, fill time. is too long, no water goes into the tub.
Technician recommended replacing the water valve, new water valve installed. We are still getting the same error code E11 no Waters enter the tub.
For model number EFLS627UTT0
Hello Dariel, thank you for reaching out. Since you have replaced the water inlet valve and that does not solve your problem, we would recommend checking the water level pressure switch, part number PS11766131, to fix the issue. It senses the water level in the tub and signals the control board to send the water in. We hope this helps, good luck with this repair!
I googled the problem, read the recommendation found the part and read that it was an easy fix. Took the broken part off the door and noticed the broke off piece was in the latch on the machine. Ordered the two parts, paid the $30 2-day delivery. Parts arrived and the machine was up and runnning in under 5 minutes
Remove two screws on attachment plate slide door lock plate out. Disconnect wire harness. Remove two screws on back side. Then reverse the process, done!
P.S. don't pay $32 for next working day it still took 3 days to arrive. doesn't help when your leaving in two.
Ruemove the back panel with a square drive bit. Belt removal was easy: rotate the large whelk while coaxing the belt off with hand pressure from behind. Comparing the old to new belts, the circumference difference was about 2”. Loop the new belt over the small motor wheel and start looping over the big drum wheel; it will be reluctant. Place a small smooth pry bar between the belt and wheel while rotating the big wheel using the bar to keep the belt on the wheel. Then turn the big wheel by hand a few times to assure the belt rides correctly.
