EER2000C00BB General Electric Range - Instructions

Removed the rear panel from the Range using the nut driver. pulled the terminal wires off the back of the heating element. Double checked if there was continuity across the heating element terminals before removing the element. If there is none, its bad. remove the two screws inside the oven holding the element in place. Once free, lift the front of the element to about 30 degrees and pull towards you. Insert the new element in the reverse manner then secure it using the two screws. Push the terminal wires onto the terminals on the back of the element and reinstall the rear panel.

Remove two screws with nut driver that holds range top down. Turn off breaker or unplug before lifting top. Brace top with 2x4. Take picture with cell phone just in case. Orient replacement part with old burner. Remove one wire at a time and install on new burner in corresponding correcting terminal. be sure they are snug. Drop top install nuts . Test! Done! I am not an electrician!!!!!!!! Please do not publish !!!!

Turned off juice
Pulled stove from wall
Unscrewed 2 screws to loosen range top
Lifted n propped top
Unplugged 4 wires
Unscrewed burner assembly
Installed burner-reversed steps to reassemble

I took the oven door off. Laid it down on a blanket on the floor. I pulled up on end going into the door, then went around with fingers to feel where the clip were and grab the clip with my fingers and gently pulled up. Then grabbed the new gasket, found the center clip that goes at top of door and started pushing the clips in. The last was feeding the ends back into the slot in the door.

1.Disconnect the power cord. 2.Remove two screws pull the element out. 3.Disconnect the wires attach to element. 4. Install the new element connecting the wires. 5. Align element with holes and tighten screws. 6. Plug in power cord and begin to cook.

lift stove top, 2 undermount screws. Then unplug 4 wires, I did them 1 at a time plugging into new burner as I go so I wouldn't screw up. Take 2 screws out of old burner to stove top, # all around circle put screws in same # on new burner.Done Good experience all the way around. Order delivery and install

This was a very simple procedure. I removed the 2 screws in the oven itself (holding the element in place), then pushed the element through the back of the oven so the wires were exposed, then slipped off the wires, the male end from the female end, I then removed the entire element. I put the new element in the over, re-attached the wires, put the screws back in place, replaced the cover, and the oven was as good as new.

I turned the breaker off to the stove and moved it away from the wall. I then removed the center cover off the back of the stove and exposed the wires connected to the bake element. I removed the wires from the bake element and then opened the oven and removed the two bolts holding the element onto the back wall of the oven. I discarded the old element and replaced it with the new first bolting the new in , then connected the two wires and replaced the rear cover. Turned on the power and made a cake.

Easy

The repair went very well. The second repair comnt to remove the hinge screws was a good correction from the first description. I had to go to that parts diagram to realize that the the two metal sleaves were insulation spacers for the two top screws.

Got door off no problem used screw drive to release locks and lifted door off. Took 3 1//4 screws out the 2 3" long screws out to separate door half's took screws of hinges and then8 1/4 inch screws of sheet metal that covered window. Replaced window and reverse what I did taking apart. Still having trouble getting 1 hinge to connect to stove. Help would be appreciated.

Really easy even i could do it , it was a little fiddly and the wires disappeared into the back of the oven , i easily removed the rear panel and pushed the wires back thru and connected them , turned the breaker back on and sparks !!
removed the rear panel again in 2 mins and saw that the wires were touching the oven frame and had shorted out , it wasnt a problem moved them slightly, reconnected them to the element tightened them up , put breaker on and Done , took about 45 mins but i could of been done in 30 with a little more care in the beginning of the job EASY !

First, my husband removed the two screws that hold in the element. Unfortunately, my GE Spectra oven had extremely short wires. That was the only thing that made it somewhat difficult. So, he pulled the element out as far as he safely could, replaced it with the new one. No problem! As I said, the only thing that made it difficult was the short wires supplied by GE. The part came from PartSelect.com with no problems. I would definitely use this website again to order parts.

Using a set of nut drivers, I unscrewed the element from the back of the stove, I unscrewed the thermometer, and unscrewed the brackets holding the element to the top of the oven compartment.

After the element was free, I pulled it out of the back of the oven, exposing the wiring. Using pliers, I disconnected the two wires, retrieved the new element, and re-connected the wires to the new element.

I reconnected the thermometer, pushed the element back into the oven, reattached it to the back of the oven and the brackets to the top of the oven compartment.

I went online, found what I thought was the correct part, ordered it, received it--WRONG ELEMENT!
HUBBY phoned parts company, very nice gal helped him find correct element, put new one in the mail to us, and we mailed back the wrong one. We received confirmation via email, and 3 days later installed the proper element. I am back to baking. I bake & mail cookies (55,000 to date) to our deployed troops, so I was lost without my oven! Thanks People!