EDW2060F03SS General Electric Dishwasher - Instructions

First I removed the dishwasher from under the counter. I turned it onto it's side so I had access to the motor and pump underneath. I determined which version of the old pump I had. I removed the old part and easily installed the new motor/pump following the directions. It took a little while for the water to begin flowing when I started it back up. Eventually it did get going.

The repair went smoothly. There were actually instructions included with the parts, so that was nice. The only "gotcha" I found was that . . . after you take off the old food-chopper, you have unscrew the old impeller from the motor shaft. This was a bit difficult and you'll want some good pliers to do it. Don't worry about stripping where the food chopper screwed on-to, that part is attached to the impeller and there is a new one on the new impeller. When I re-installed everything onto the dishwasher, it rattled the first couple of times while the wear-ring was finding it's seat. Don't worry, that's normal. It went away by the third wash. I think I still have a small crack in the pump housing, though. The pump housing is two halves of molded plastic fused together along a seam, and I think the seam is starting to leak. It's about one drop every 45 seconds. I'm thinking JB Weld will fix it.

The motor seized up on my 1990 GE Dishwasher
Repair would cost 360. Replacement about 600
I ordered the motor and pump from PartSelect for 137..44
Remover the under counter washer (it‘s very light) and removed the water and drain line and disconnected the power. Turned the washer on it’s top to access the motor and pump and removed the electrical plug in lines, and the clamps holding the pump on to the connections. Replaced it with the new motor and pump, reconnected the electrical plug ins, added an adapter hose part, tightened the original clamps then reconnected the water, drain and electrical connections and reinstalled the washer. All in about an hour, The only glitch was the grounding screw for the ground wire on the motor. The screw was too long to tighten. Substituted the original shorter ground screw from the old motor, and that worked fine. Only used 4 parts from the large assortment of parts supplied.
Immediately ran the washer through a cycle, all worked perfectly.

Since the pump and the motor was a single unit, I removed the assembly by disconnecting the electrical plugs and drainage connections. This was a very simple installation. I reversed the above steps, reinstalled the dishwasher and all worked out well.

This was one of the easiest fixes i have ever done. All you need is a screwdriver. the hardest part about it was unscrewing the old spray arm. I found it was easiest to break the tabs on the old spray arm and pull out the spray tower, leaving the bottom part in. The bottom is the part to unscrew. I then put the metal end of the screwdriver through the two holes where the tabs were and used the screwdriver as a handle to unscrew it. Once it was taken out, I screwed the new spray arm in - buy hand -. You can feel it lock when it is all the way in.

First make sure the dishwaher is off and secure to work on: remove the lower basket, turn the broken spray arm assy counter clockwise, it may be tight, but no tool be need it, screw it all way out, remove it and replace it with your new one by turning clockwise,make sure its tight, no tools need it but basket in place and the dishwasher is ready to go

Opened the package and screwed in the new rinse aid fill cap. No problems. It fit and works just fine.

I only had to remove the inside door panel then the bad control panel , a total of 10 screws, and then plug in the 3 harnesss wires. FIred it up and worked like a champ!

I pulled the dishwasher out and detached the drain hose. I attached the new drain hose after cleaning out the connection to the garbage disposal.

Now my dishwasher doesn't stink anymore!

Once the new motor and pump kit arrived. I removed the dishwasher, turned it upside down and replaced the motor and pump with the new one per the directions. Difficulty came in feeding the electrical wire/plug back through the cabinets. Once done, turned on the dishwasher, filled the tub, then manually moved the dial to drian. The water still would not drain from the tub. I searched further for the problem. Here it is; Found the air gap tube was plugged with food. Once I removed, cleaned and reinstalled the air gap, the tub drained fast and everything works great. So, I hope you folks put this up in your troubleshooting section for others to check before buying a pump and motor kit. If you had, I would have been able to check out the air gap, clean it out first before spending $140.00 for a pump and motor kit I didn't need. Anyway, lessons learned..Jeff

First I looked for blockage and found none.I took the pump off and hooked power to it in my work shop and it did spin when powered up.We had broken a glass in the washer and thats when the problem started. I did find a few small pieces in the check valve assembly. It did not look bad but for cheap I ordered the part. Ran the washer and it drained on the wash but not on the final. Turned off the power.Slid the wash out where I could get to the power and not unhook the water. Turning off the power I disconnected the wires and carefully turned the power on and touched them to the pump and forced it to drain knowing that the pump worked I thought it would at least empty the water. I touched the wires to the pump and the board clicked the water drained. Hooked it back up. Ran it and has been working great since.

Replaced with a new rinse aid fill cap.

Removed the old one from its slot and slid the new one into it.
No instructions needed.

Removed 4 screws, took off basket covering, put new part in one turn, then replaced covering. Plumber had come out, I watched what he did, he had to order part and come back. I asked how much he didn't know but said cheaper than buying a new dishwasher. When he left I started calling around about the little plastic part that I needed. Part was $15.50. They called and said it would be $110.00. Needless to say I called them out and ordered the part myself and put it in. Took me like 6 minutes and cost $21.69. I was so mad about this situation that I even got my service call money back that I had already paid.

Took four screws out, unscrewed the piston & nut assembly by hand installed the new one. Cycled the dishwasher & it worked perfectly.