DXPW3228 (Type 0) DeWALT Pressure Washer - Overview
Sections of the DXPW3228
[Viewing 2 of 2]_WW_1.gif "Page A Diagram and Parts List for Type 0 DeWALT Pressure Washer")
_WW_2.gif "Page B Diagram and Parts List for Type 0 DeWALT Pressure Washer")
Keep searches simple, eg. "belt" or "pump".
Hose Chemical
PartSelect #: PS9963814
Manufacturer #: 5140094-96
This is a genuine DeWalt replacement part that has been sourced from the original manufacturer to be used with pressure washers. The clear plastic hose is used to carry detergent from the chemical tan...
$83.93
Special Order
Nozzle Holder Rubber
PartSelect #: PS9963815
Manufacturer #: 5140094-99
This is an authentic DeWalt replacement part manufactured for use with pressure washers. The rubber nozzle holder attaches to the handle assembly or dashboard and is used to stow the nozzles. This noz...
$65.89
Special Order
Foot
PartSelect #: PS9963819
Manufacturer #: 5140095-03
This genuine OEM part is made to fit the DeWALT machines listed below. This rubber foot attaches to the underside of the frame, dampening vibrations and keeping the machine stable while protecting sur...
$76.77
Special Order
Valve Thermal Relief
PartSelect #: PS9963872
Manufacturer #: 5140095-85
This thermal relief valve is a genuine part produced by the original manufacturer for DeWALT pressure washers. The valve connects to the pump and protects it from overheating. If the pump gets too hot...
$78.38
Special Order
Common Symptoms of the DXPW3228
[Viewing 2 of 2]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Pressure washer came up to pressure ,squeeze trigger, total pressure loss
This is on a dewalt pressure washer with A 8.7 12 pump and Honda motor. Removed brass housing taking really good notes of how seals were placed Into housing
This pump is a triplex pump. Removed 3 brass Allen head plugs to expose the 3 checks and the other 3 checks are at the bottom of other 3 ports where the 3 pistons go in.
Used a needle nose plies to remove checks..Removed seals from piston ports. I used a Oring lubricant to assemble THE NEW SEALS THAT GO IN FIRST WERE VERY VERY HARD TO INSTALL HAD TO PUSH THEM IN THEN SLOWLY WORKED AROUND THE EDGE OF SEAL SLOWLY WORKING DOWN INTO BORE OF HOUSING
THE rest of parts install went easy Bolted unit up,pulled starter rope to rotate pump an motor ok so far
Hooked up water started motor and cleaned items I had out to do. Hope info helps
This pump is a triplex pump. Removed 3 brass Allen head plugs to expose the 3 checks and the other 3 checks are at the bottom of other 3 ports where the 3 pistons go in.
Used a needle nose plies to remove checks..Removed seals from piston ports. I used a Oring lubricant to assemble THE NEW SEALS THAT GO IN FIRST WERE VERY VERY HARD TO INSTALL HAD TO PUSH THEM IN THEN SLOWLY WORKED AROUND THE EDGE OF SEAL SLOWLY WORKING DOWN INTO BORE OF HOUSING
THE rest of parts install went easy Bolted unit up,pulled starter rope to rotate pump an motor ok so far
Hooked up water started motor and cleaned items I had out to do. Hope info helps
Parts Used:
-
Stephan from MANSFIELD, OH
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set, Wrench set
6 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!