DLL1550PD Hotpoint Dryer - Instructions

just changed out the gas igniter very simple to do thanks

1. removed old switch 2.wrote model # 3. went to web site found part 4. ordered part 5 part came in 2 days 6. installed part in 15 min. works like new saved over 95.00 thanks ed

First I shut off the gas and unhooked the gas line. Then opened the door and removed the screws that hold the top down in the front. I then tipped the top back so I could get to the top of the drum. I removed the screws ( 4 ) inside the door opening and slid the felt seal back. Next I put the belt in the drum and feed part out the crack between the drum and the dryer frame, being careful not to cut the belt. I woorked the belt around the crack and pulled it toward the drum. When I got the belt through it was all the way around the drum and I just put the belt over the motor pully and pulled the tensioner back and wrapped the belt over it. Put all the screws back in and the back on and fired it up. Works as good as it ever did.

Remove the bottom cover of dryer to look at the motor, see belt hanging remove broken belt. Remove screws from the top and front, slide belt over drum put small piece of tape to hole belt in place replace screws go back to the rear pull belt over the motor pulley close back panel

First I took the lower bottom off the back of the dryer (bolts), pulled the old pulley off the idler and put new one on. Second, I took the screws out in front (under lip of top) and then removed bolts from bottom of the front. Then lifted lid up and swung front to the side. I was then able to take the drum out and clean it before putting it back in with the new belt. The put everything back together.
Dryer ran for ten mintues and then quite again. Seems to be in the motor and not the less expensive parts I found to be worn.

I follow the easy instruction by a user in your web site to reach the problem area and discoverd the drive belt was broken.
As it turned out, the problem was compounded when I discovered also that the Heating element needed replacement.
At this point I decided it was time to let go and got a new dryer, choosing the same brand that lasted 25 years: GE

Replaced gas igniter The part came a day after I ordered it. I really liked the speed of delivery.

Removed Front of Machine, removed access panel on back of machine, reassembled after installing belt and cleaning out machine. Pretty Easy, hardest part is getting around the front of the drum.This machine has been going since 1978. 31 years, 2nd replacement belt and thats all, not bad, the washer that was bought at the same time went around 6 years ago, havent had the same luck, since then, two machines and the latest one is giving me problems already. They dont make them like they used to.

First unscrew the two screws at top to disconnect the control panel. Lay unit on the back. Remove door(be careful not to lose washers and hinges). Remove four screws to lift off top. Wiggle drum, slip belt over drum. Replace door, then put Four screws back in place.Stand unit upright.Remove back panel, you should see belt hanging.Pulley wheel is in front of you.Follow instuctions sent with pulley wheel.Reattach you're ready to roll, make sure you sllip the belt on the drum until the drum spins.

My Daughter did it for me .

Unplug the dryer, turn off the gas. Opened the lower front door panel. She disconnected the gas pipe from the igniter assembly. Then She removed the two screws holding the assmb. Then she removed the wire from the front of the assmb. and the white and black wire from the back of the unit. remove the old igniter put in the new one put it back together.

Backwards to start- here's the correct way.Disconnect power and vent hose-tip onto front-remove bottom plate allowing access to bottom of dryer and the belt pulleys-remove the small plate in center and under that is a C-clip holding the drum shaft in place-remove the clip and washer-sit dryer upright - open the door and remove the 4 screws under the upper lip which hold the top of the dryer in place-lift up top and secure or have someone hold it up.-inside the top front on both sides are 2 screws per side and there are 2 screws at the bottom under the kick area, remove all 6 of these screws and the front of the dryer will come off-watch the wires-with the front off you can pull the drum forward to allow installing the new belt. - hold the new belt in place with a couple of pieces of tape-reverse the procedure to put drum back together and then thread the new belt onto the drive pulley and under the idler tension pulley.- reinstall back plate, vent hose, power and you're ready to go have a beer.

1. removed old switch 2.wrote model # 3. went to web site found part 4. ordered part 5 part came in 2 days 6. installed part in 15 min. works like new saved over 95.00 thanks ed

Removed the screws that hold the draying unit (barrel) to get accest to the back of the switch, and that's when I noticed that I will need the belt and I ordered to when my existing belt goes I have a replacement.

First I checked on-line "how to change a dryer belt" and followed the instructions. Remove front panel and slide belt over drum, in the back, put belt around pulley and hand trun the drum. on-line instructions had pictures to ensure proper install. It was easy.

Unplugged machine and turned off the gas. Removed top panel,4 screws along inside top edge of door opening. Used a wooden shim to pry the drum away from the surrounding "lip with felt padding. Slipped belt through.the trick is getting the belto around the entire drum. First I got it over the top of the drum, and fed it around the bottom by turning the drum and pushing the belt through the opening made by the shim between the bottom of drum and the lip with felt. It was kind of like feeding a bicycle chain onto a sprocket as you turn the wheel..
Removed back panel and vent hose, removed old belt laying on floor of machine, fed the belt onto the motor pulley and the tension pulley. Tension pulley presses on top side of belt. Belt should be in same position on drum as old belt, you can see a friction mark all around the drum from the old belt.
Replaced panels and vent hose. Put felt padding back into place wherever it slipped out. Very important because if you don't it scrapes the drum when turned on and makes a loud sound.
Dryer works perfectly again.