The Dryer's Lint Filter is used to collect lint during the dryer cycle as it passes through the dryer vent, in order to prevent damage to the machine. This manufacturer-approved part comes in gray, me...
This is an authentic dryer lint filter cover sourced directly from the manufacturer. It protects the more delicate lint filter in your dryer, so that it doesn’t get damaged and lint can’t mix in with ...
This is a replacement lint screen guide for your dryer. The lint screen guide attaches to the front bulkhead and supports the lint screen. If your lint screen will not stay in place, or if you are not...
The drum roller for your dryer holds the drum in place while the drum turns on the support wheels. The drum roller is round with a bearing in the middle and measures approximately 3 inches in diameter...
Ask our experts a question about this model and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
James
February 2, 2020
My dryer shuts off before the cloths are dry.
For model number DLEX3570V
Hello James,
Thank you for your question. Our sources suggest replacing the sensor under part PS3529161 for your model to fix the issues with the dryer. We hope this helps.
For this parts # K250 or K251 do they are the same ?
I need the roller kit assembly, I thing its 4 of them I need. Which parts # I need to order ?
Thank you
For model number DLEX3570V
Hi Patrick,
Thank you for your question. Yes, K250 and K251 are the same. It consists of one roller and one tri-ring. You will need to purchase 4 of them. If you have any questions, please let us know. We are open 7 days a week. We look forward to hearing from you!
Was this helpful?
Thank you for voting!
Danielle
June 2, 2023
LG LINT FILTER CATCHES CLOTHES ON THE LIP THAT PROTRUDES FROM RIGHT SIDE. HAVE CLEANED THE FILTER AND THE FILTER RECEIVING RECEPTACLE OF LINT. THE FILTER DOES NOT SIDE IN ALL THE WAY.
WHAT IS NEEDED TO FIX THIS PROBLEM
For model number DLEX3570V
Hi Danielle, thank you for contacting us. We would suggest checking the lint screen housing, part number PS3534930. Make sure it is clean and not damaged. A damaged housing might cause the lint filter to not properly slide in. We hope this information helps!
How do you know if something wrong with main control board
For model number DLEX3570V
Hello Jeffery, thank you for your inquiry. According to our research, the main control board, part number PS10065064, can be accessed and tested. There will be three rectangle boxes on the control that will have two wires going to each one. The relay with the black wire and the brown wire would be tested for voltage after starting a cycle. If there is not 120VAC at the brown wire when testing with a meter to ground, the main control board has failed and needs to be replaced. We hope this information helps!
Had to replace front drum support rollers. Removed screws underneath top in back that held bracket that keeps top in place. Slid top towards rear and lifted up. Removed 4 screws that hold plastic front panel in place (inside..2 on each corner) Unplugged front panel electric plugs to remove panel. Opened door..removed 2 screws at bottom of door opening. Removed screws on top of front panel. Unplugged door switch plug. Removed front panel. Removed right front roller with 9/16th wrench for nut. Adjustable for back of stud. Lifted up on drum to get roller out. Reversed to install. Left roller a bit harder to get to stud. Removed and installed same as right side. Did not attempt to replace rear rollers. Have them if needed but very much more involved to replace.
I actually went to mr fix it on u tube. Great instruction on how to take dryer apart. First I unplugged the dryer. I found I could reach the heating system by removing the lint tube in the back of the dryer. I put my I phone with the light on inside the back of the dryer and tested the connections to see if all were working. The thermal fuse was not working. I removed the two wires , red on top and white on the bottom. Then used a small Phillips screwdriver to remove the two mounting screws and removed the fuse. I then used a vacuum to clear any lint from the back of the dryer and inside the dryer. This took me about an hour and a half. I did it this way because I did not want to disassemble the entire dryer to get to the components. I received the fuse in 3 days and tested it. It was fine. I then put it in the dryer screwed it in place, connected the wires. Replaced the lint tube. This took about 10 minutes. Dryer is running great.
Removed existing parts using screwdriver, positioned new parts in dryer and re-inserted screws, tightened - done. Piece of cake, even for someone who cannot saw a straight line with a chop saw.