The drum roller for your dryer holds the drum in place while the drum turns on the support wheels. The drum roller is round with a bearing in the middle and measures approximately 3 inches in diameter...
$163.39
In Stock
Order within the next 5 hrs and your part ships today!
This part has the felt strip and is used to collect lint as it passes through the dryer vent. The lint filter in your dryer is used to collect lint as it passes through the dryer vent. If you notice t...
$84.67
In Stock
Order within the next 5 hrs and your part ships today!
This plastic adjustable dryer leg is used to support the weight and adjust the height of your dryer to keep it level. To install the leg, tip the dryer back and screw it into the bottom of your dryer ...
$13.95
In Stock
Order within the next 5 hrs and your part ships today!
Questions And Answers for DLEX2650R
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Loretta
April 4, 2023
My dryer keeps saying check filter and it’s clean
For model number DLEX2650R
Hi Loretta, thank you for reaching out. According to our research, it is just the machine asking you to check the filter. It will show this message before every drying cycle. As it is already cleaned, the indicator light will go off after the next cycle or after restarting. We hope this information is helpful!
Was this helpful?
Thank you for voting!
Refugio
July 3, 2023
My dryer is not drying clothes no heat only cold air
For model number DLEX2650R
Hi Refugio, thank you for reaching out. We have researched the model and would suggest checking the heater assembly, part number PS3527790. It produces the heat to dry the clothes in the dryer. If faulty, it may not generate enough heat or even no heat at all to dry the clothes. We hope this information helps!
Hello Scott, thank you for the question. According to our research, we would recommend checking the door switch, part number PS3529308, to fix the issue. We hope this helps!
Dryer display quit working, and will not turn off when door is closed.
For model number DLEX2650R
Hi Paul, thank you for your question. If your display is no longer working, you will need to replace your display board, part number: PS3646018. Good luck with your repair.
Was this helpful?
Thank you for voting!
Betty
January 20, 2023
My dryer makes a noise but cuts off and wont turn drum, cannot be turned by hand.
For model number DLEX2650R
Hello Betty, Thank you for the question. We suggest checking the Belt for wear or damage. if the belt is good you may have a faulty Motor. We hope this solves your problem!
Had to replace front drum support rollers. Removed screws underneath top in back that held bracket that keeps top in place. Slid top towards rear and lifted up. Removed 4 screws that hold plastic front panel in place (inside..2 on each corner) Unplugged front panel electric plugs to remove panel. Opened door..removed 2 screws at bottom of door opening. Removed screws on top of front panel. Unplugged door switch plug. Removed front panel. Removed right front roller with 9/16th wrench for nut. Adjustable for back of stud. Lifted up on drum to get roller out. Reversed to install. Left roller a bit harder to get to stud. Removed and installed same as right side. Did not attempt to replace rear rollers. Have them if needed but very much more involved to replace.
I actually went to mr fix it on u tube. Great instruction on how to take dryer apart. First I unplugged the dryer. I found I could reach the heating system by removing the lint tube in the back of the dryer. I put my I phone with the light on inside the back of the dryer and tested the connections to see if all were working. The thermal fuse was not working. I removed the two wires , red on top and white on the bottom. Then used a small Phillips screwdriver to remove the two mounting screws and removed the fuse. I then used a vacuum to clear any lint from the back of the dryer and inside the dryer. This took me about an hour and a half. I did it this way because I did not want to disassemble the entire dryer to get to the components. I received the fuse in 3 days and tested it. It was fine. I then put it in the dryer screwed it in place, connected the wires. Replaced the lint tube. This took about 10 minutes. Dryer is running great.
I followed video instruction in disassembling and set screws from each section into diferent small bowls in the order they were removed. Hardest part was some of the screws were really hard to get loose without stripping them and my control panel did not match video but I figured it out. Replacing the parts were easy and putting it back together. While it was apart I cleaned everything including fan blower wheel. Thanks for the right parts and your online video. With your help and a prayer this 62 year old woman fixed the problem and dryer runs like new.