The drum roller for your dryer holds the drum in place while the drum turns on the support wheels. The drum roller is round with a bearing in the middle and measures approximately 3 inches in diameter...
$163.39
In Stock
Order within the next 6 hrs and your part ships today!
This part has the felt strip and is used to collect lint as it passes through the dryer vent. The lint filter in your dryer is used to collect lint as it passes through the dryer vent. If you notice t...
$84.67
In Stock
Order within the next 6 hrs and your part ships today!
This plastic adjustable dryer leg is used to support the weight and adjust the height of your dryer to keep it level. To install the leg, tip the dryer back and screw it into the bottom of your dryer ...
$13.95
In Stock
Order within the next 6 hrs and your part ships today!
Order within the next 6 hrs and your part ships today!
Questions And Answers for DLE5955G
Ask our experts a question about this model and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Tammy
January 31, 2020
Our dryer is not heating. The cooling indicator stays on solid and the heating indicator is flashing and there is no heat. Not seeing any error codes.
For model number DLE5955G
Hi Tammy. You may wish to test the thermal fuse, thermister and blower thermostat. Thank you for your question and good luck with your repair.
hello, hoping you can help. the dryer is functioning but not getting warm or hot at all. ive done some research and there are so many aftermarket parts that i would not attempt to use. can you please advise as to all components i would need to change to correct the issue and then assist me in placing an order with you ?
best regards,
Tony D'Angelo
9175259945
For model number DLE5955G
Hello Tony, thank you for contacting us. We would recommend checking the following parts to fix your issue: The thermal fuse, part number PS3530485, the dryer thermistor, part number PS3529026, the thermostat, part number PS3530482, and the heating element, part number PS3527790. We look forward to hearing from you if you need assistance with placing an order through our 7-days-a-week customer service. We hope this helps!
My dryer runs but there is very little heat. Any suggestions
For model number DLE5955G
Hello Butch, thank you for your inquiry! Our research indicates that the issue is probably with the Thermal Fuse, part number PS3530485. If that is not the problem or if you have already fixed that, then the problem would be related to the Dryer Thermistor, part number PS3529026. Customer service is available 7 days a week if you need help placing an order. Glad to be of assistance!
Hi Pat, thank you for reaching out. The following parts need to be checked to fix the issue: the thermal fuse, part number PS3530485, the thermistor, part number PS3529026, the blower thermostat, part number PS8747887, and the heater assembly, part number PS3527790. We hope this information helps! If you need help placing an order, customer service is open 7 days a week. Thanks again for your great question.
Had to replace front drum support rollers. Removed screws underneath top in back that held bracket that keeps top in place. Slid top towards rear and lifted up. Removed 4 screws that hold plastic front panel in place (inside..2 on each corner) Unplugged front panel electric plugs to remove panel. Opened door..removed 2 screws at bottom of door opening. Removed screws on top of front panel. Unplugged door switch plug. Removed front panel. Removed right front roller with 9/16th wrench for nut. Adjustable for back of stud. Lifted up on drum to get roller out. Reversed to install. Left roller a bit harder to get to stud. Removed and installed same as right side. Did not attempt to replace rear rollers. Have them if needed but very much more involved to replace.
I actually went to mr fix it on u tube. Great instruction on how to take dryer apart. First I unplugged the dryer. I found I could reach the heating system by removing the lint tube in the back of the dryer. I put my I phone with the light on inside the back of the dryer and tested the connections to see if all were working. The thermal fuse was not working. I removed the two wires , red on top and white on the bottom. Then used a small Phillips screwdriver to remove the two mounting screws and removed the fuse. I then used a vacuum to clear any lint from the back of the dryer and inside the dryer. This took me about an hour and a half. I did it this way because I did not want to disassemble the entire dryer to get to the components. I received the fuse in 3 days and tested it. It was fine. I then put it in the dryer screwed it in place, connected the wires. Replaced the lint tube. This took about 10 minutes. Dryer is running great.
I followed video instruction in disassembling and set screws from each section into diferent small bowls in the order they were removed. Hardest part was some of the screws were really hard to get loose without stripping them and my control panel did not match video but I figured it out. Replacing the parts were easy and putting it back together. While it was apart I cleaned everything including fan blower wheel. Thanks for the right parts and your online video. With your help and a prayer this 62 year old woman fixed the problem and dryer runs like new.
