The drum support roller for your dryer holds the drum in place while the drum turns on the support wheels. The drum roller is round with a bearing in the middle and measures approximately 3 inches in ...
$182.93
In Stock
Order within the next 8 hrs and your part ships today!
This part has the felt strip and is used to collect lint as it passes through the dryer vent. The lint filter in your dryer is used to collect lint as it passes through the dryer vent. If you notice t...
$84.67
In Stock
Order within the next 8 hrs and your part ships today!
The moisture sensor, also known as a humidity sensor, works in conjunction with your dryer by helping determine the amount of moisture in the drum to reduce overdrying. If the timer doesn’t advance co...
$28.25
In Stock
Order within the next 8 hrs and your part ships today!
Looking to extend the lifespan of your LG electric dryer? Our authentic LG Idle Pulley could be the missing piece you need! This little thing plays a big role in keeping your dryer working smoothly an...
$42.63
In Stock
Order within the next 8 hrs and your part ships today!
This plastic adjustable dryer leg is used to support the weight and adjust the height of your dryer to keep it level. To install the leg, tip the dryer back and screw it into the bottom of your dryer ...
$13.88
In Stock
Order within the next 8 hrs and your part ships today!
Take a look at this essential LG Dryer Safety Switch Assembly. A don't-miss fixture for your LG Dryer. This is more than just a part, it's a safeguard for you. If your dryer's door springs open, this ...
$56.87
In Stock
Order within the next 8 hrs and your part ships today!
Questions And Answers for DLE2050W
Ask our experts a question about this model and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Bob
April 1, 2023
Does not shut off continues to run with no lights on
For model number DLE2050W
Hi Bob, thank you for your question. To fix the issue, you will need to replace the door switch, part number PS3529308. We hope this helps!
My dry want start unless i push the start button and push the door in
For model number DLE2050W
Hi Lawrence, thank you for reaching out. Based on our research, the issue that you are facing is because of the door switch, part number PS3529308. Door switch prevents the dryer from running when the door is open. We hope this solves your problem!
Dryer runs but only blows cold air. What do I replace?
For model number DLE2050W
Hello Janice, thank you for your inquiry. We suggest you checking the thermal fuse, part number PS3530485, to fix the issue. We hope this helps, good luck with the repair!
Hi Joe, thank you for reaching out. We would suggest replacing the dryer thermostat and thermistor kit, part number PS16878105. It monitors and helps regulate the dryer temperatures. We hope this solves your problem!
Had to replace front drum support rollers. Removed screws underneath top in back that held bracket that keeps top in place. Slid top towards rear and lifted up. Removed 4 screws that hold plastic front panel in place (inside..2 on each corner) Unplugged front panel electric plugs to remove panel. Opened door..removed 2 screws at bottom of door opening. Removed screws on top of front panel. Unplugged door switch plug. Removed front panel. Removed right front roller with 9/16th wrench for nut. Adjustable for back of stud. Lifted up on drum to get roller out. Reversed to install. Left roller a bit harder to get to stud. Removed and installed same as right side. Did not attempt to replace rear rollers. Have them if needed but very much more involved to replace.
I actually went to mr fix it on u tube. Great instruction on how to take dryer apart. First I unplugged the dryer. I found I could reach the heating system by removing the lint tube in the back of the dryer. I put my I phone with the light on inside the back of the dryer and tested the connections to see if all were working. The thermal fuse was not working. I removed the two wires , red on top and white on the bottom. Then used a small Phillips screwdriver to remove the two mounting screws and removed the fuse. I then used a vacuum to clear any lint from the back of the dryer and inside the dryer. This took me about an hour and a half. I did it this way because I did not want to disassemble the entire dryer to get to the components. I received the fuse in 3 days and tested it. It was fine. I then put it in the dryer screwed it in place, connected the wires. Replaced the lint tube. This took about 10 minutes. Dryer is running great.
I followed video instruction in disassembling and set screws from each section into diferent small bowls in the order they were removed. Hardest part was some of the screws were really hard to get loose without stripping them and my control panel did not match video but I figured it out. Replacing the parts were easy and putting it back together. While it was apart I cleaned everything including fan blower wheel. Thanks for the right parts and your online video. With your help and a prayer this 62 year old woman fixed the problem and dryer runs like new.
