DIST333JTGWW General Electric Dryer - Instructions

1st - removed the two screws inside the front door panel. They are somewhat hidden up underneath so you may have to look for them. 2nd - I removed the top of the dryer cabinet by lifting it out of the clips holding it in place. 3rd - removed the two screws (one on each side) in the o=uppper corner of where the side panels connect the front panel. These are about 3/4" phillips head screws. Then the front panel could be moved to one side of the dry. 4th - remove the drum by lifting it up and out the open top area. 5th - add the new belt to the dryer tub (rib side towards the drum) and replace dryer tub to its original position. 6th - reaching in underneath the tub you need to pull the ideler pulley toward the center of the cabinet while laying the belt on the "outer side" of the ideler pulley and at the same time fitting the belt over the small pulley located on the motor. Once that is done, you reassemble in reverse order and should be good to go.

Both parts arrived quickly and were exactly what I ordered. The lint screen replacement part was of higher quality and it works better than the one that came with the dryer. Very satisfied.

Used an allen wrench to remove the heat deflector and used allen wrench to replace it with the new one. HINT!! Do not lean on the inside of the dryer!!!!!!

Unscrewed three screws on back and removed the switch and inserted the new one. There are 3 wires that clamp on the switch. Remember to unplug before doing this.

Real easy and great people to work with. Much cheaper than a technician repair.

Jim

took out broken filter and replaced with new lint
filter.

I narrowed the porblem down to the rotary start switch, which is located in the top panel. It takes a hex wrench to remove the four screws holding the fron top panel in place and of course the knobs had to be removed. The switch rotates about a wuarter of a turn to come out. Label and remove the three connectors (3). It took about a week to get the replacement part which was slightly different than the original part. The good thing is it had the three prongs like the old part.. I hooked the connectors in the same configuration as the old switch, plugged the power cord back in to test and it started right up.

I had to remove all screws from the back of the dryer, control panel, and one side. Pulled top off. Took out two screws that held front door panel on. Disconnected 3 wires into door and completely removed door panel. Disconneted pink wire from heating element then slide belt off drum as I removed the drum. Pulled off the old completly worn out drum bearing sleeve and replaced it. Replaced drum slides as some were worn through. Had a little trouble getting belt back on when I reconnected everything but for 50 dollars in parts and shipping I have working dryer, so I would say it was well worth the effort.

Pulled off old knob put on new one

I just pressed the latch with my thumb, the latch went in, and voila....job done. Thank you

Removed the broken handle from the dryer and popped on the new one.

Open it up. Try to fix with duct tape. Test. Fail. Order parts.

Put slides on, open it up, put parts on door, align drum, close it up.

Start, smile and BRAG!!!!

Works faster, fluffer clothes and I'm a happy Mom because now I can run whenever and there is less wrinkles.

We removed two screws to remove the top and two screws to remove the front. The dryer drum slides were easy to replace and the felt fit into a track. It was so easy and now my dryer is quiet again, no more rubbing/squeaking. I can't believe that was all we had to do, and for $60.00!!! I'll be back for future parts if needed. Thanks.

Ordered new lint filter, received it in 2 days, removed old filter, snapped in new filter, patted myself on the back .

The part was delivered in record time. That was the best part. And it fit perfectly and was the correct color. The other filter was grey and the dryer is white. Thanks for being so efficient.

Unplug. Remove 3 knobs at front of panel. Remove 4 screws. Panel pulls forward. Remove green grounding wire to allow panel to come forward more. Pry up locking tab on switch. Turn switch to unlock from panel. Install new switch in reverse order of removal. Pull off each wire one at a time from old switch and attach to new switch. Reinstall panel and insert 4 screws. Done. My wife was so suprised that it actually worked and I fixed it in less than a day! Only took about 20 minutes. Thanks Part Select and the other repair stories that I read on your website.