DG170AXH3 Westinghouse Dryer - Instructions

Watched video on you tube went to PartSelect web site determined it was the rear bearing from the probable causes listed. Received part in two days and the job took less than thirty minutes. The limited access to the belt motor was the only difficult part of the job but by putting the belt on the idler pulley first and pulling down on the belt I was able to get it over the motor pulley. Thanks PartSelect for making this job easier than I thought it would be.

Flame Sensor didn't fix it but, it was easy to replace. Unplug electric. Lift up the top and remove wires from switch and light switch. Remove screws that hold on the front and remove front panel by lifting up and out. Sensor is on the left side of the burner, held on with just one screw. EASY!

Exactly how the video showed! It was super easy and I am a girl...although I am a lil more mechanicly inclined than most girls, it was a piece of cake!

The customer had removed the top cover hinges and the rear cover plate to recover the broken belt. I first removed the four screws holding the front panel and tilted it out to allow access for the new belt. The drum dropped about 2-3". Fed the new belt over the drum with the printing'This Side Up' facing me, lifted the drum up as I closed the front cover over the felt on the front rim of the drum. Replace dhtew four screws. Door switch leads were long enough to allow the front cover to tilt forward so did not remove. Next engaged the motor pully and tension pulley, then rotated the drum manually to assure tracking and no twist in the belt. Vacuumed the wall passthrough pipe,the flex vent tubing and the motor compartment of lint. Closed up the back cover and drove the 52 miles back to my shop.

This is a front load dryer. First unbolt top cover of dryer. Then unbolt screws and connections to control panel. Next unbolt all screws holding dryer door and front bottom panel. Next take belt off of drum and slide out drum from the front. From inside of drum remove 3 screws and remove bearing then put new bearing on and bolt up the same way you take old one off. Using an 8mm socket or wrench remove plastic bearing cage located at rear of dryer. When unbolting there is a retaining clip and small steel ball to be removed from back of dryer. Replace this the same way you take it off. He sure to grease the bearing cage then replace everything back from putting the drum in first to your last step bolting on top cover of dryer. Hope this helps anyone doing this repair.

Had the macnine apart before ordering the Bearing Assembly. Reading other comments convinced me to order the Bearing Assembly. Parts were shipped very quickly after ordering and following the instructions on the web site things went back together easily.

followed the Video instruction which were provided. Dryer works like brand new.

I used the video, and it helped me a lot! I got the drum out, installed the new bearing, greased the new shaft and the receptacle, then I reassembled. When I tested it, mine was still very noisy, so I removed the drum once more and cleaned/added some grease on the tensioner bearing. This was the cause of the noise in my case, but the bearing & housing were nearly shot, so something would have given out very soon. I would suggest to grease the tensioner the first time to save time and effort. (And save some of the grease for the tensioner pulley). SAFETY TIP: there was also a ton of lint that got trapped inside the unit!!! Clean your dryer once per year to prevent it becoming a fire trap!

Once I received the product I placed it in the hole and it worked great.

i watched the video that is furnished at parts select, it was very useful in doing this repair. i would strongly recommend watching this as i did install the ground bearing wrong to start with,and restringing the drum belt is something you have to feel as your installing it back in place so the video is useful for that as well. my repair was on a front load dryer made by Frigidaire,

The other door latch broke and fell out. I simply pushed the New Door Latch in the hole, and it snapped into place.

Inserted clasp in frame of door

My son kept slamming the door wrong and eventually the catch broke and two and feel out. My husband is the handy man of the family, but has been so busy that I was just duck tapping the door close. Finally, I decided to see if I could look up the part. Found it on here, ordered it, and replaced it all myself! Proud mother right here! Very easy. Works great.

followed vidio instruction which made it easy

purchased bearing kit