DECSFW4 Frigidaire Dryer - Instructions

replaced rear drum bearing kit. Watched video made it real easy. The only problem was getting the belt back on the pulleys.

Watched video sent to me after I purchased belt on line. Super helpful!

I looked up a YouTube video on my specific model. Found one that said “basic disassembly”. I watched that and had it apart and back together in no time. Very easy to take apart and put new parts back in it. Re-assembled and since the repair no squeaking.

First I took the drum out of the dryer. This was an easy tear down. I had to remember 2 wires, and a belt assembly ( 2 pullies ). I removed 3 screws inside the drum to release the bearing assembly from the back. Then I went to the dryer chasis and removed the mounting bracket by removing 2 screws. I simply replaced the mounting bracket with the new one. This required having to use a magnet to hold a small ball bearing in place while I worked the rest of the pieces in position.I greased it up and went back to the drum. I replaced the old bearing assembly with the new one. Easy. I took the time to shop-vac the inside of the dryer. There was a lot of loose lint, candy rappers, coins, etc. Finally, I put it back together. Unfortunately, this is the forth (4th) time I've had to do this. It's cheaper than buying a new dryer. Now, I've got to fix the washer.

Removed back panel. Popped off top of dryer, then removed front of dryer. Slid belt onto tumbler, put front cover back on, put top back on and adjusted belt frombottom panel cover.

First I removed power from dryer. Then I lifted the lid and removed the 2 screws holding the front onto the dryer. I then used a pair of pliers to grip the seal and help pull it off. Cleaned off old adhesive. Recommend getting GOOP BE GONE. Then apply high temp sealant onto area and place seal on top. Press firmly across it to make sure it is in place. Then put it all back together and your done. Also, if upper seal is worn.recommend ordering lower seal at same time. I didn't and should have. Save yourself from doing this twice.

Open the top cover by pushing the retention clips in from the front (just under the top edge) with the putty knife - that was the hardest to figure out - I found it online.
The rest is just 4 screws - 2 inside to release the plastic filter holder and two on the inner edges of the front panel.
Took the front off, ripped the old slider, cleaned the glue residue with alcohol and mineral spirits and a lot of scrubbing, vacuumed all the lint from the fan.
Then glued the new slider in place and clamped it together. Didnt know how long the glue takes so I left it overnight, just in case.
It works well now. Cleaning the ducts and the fan with the vacuum hose made a world of an efficiency difference. They should make an easy way to do this for regular maintenance!

there are several srcews to remove. there are some u dont have to take out but it looks like u do.ease of the front panel and remove the old drum glide,very hard to get of all the felt.check the the bottom guide before u order parts if possible(i could've replaced mine,but didnt have time to check it first).when glue back in place follow directions exact and clamp.allow glue to dry as long as u can. mine set overnight it was nice and dry(if u dont you'll be doing it all over again)replace everything as you took them off.all works great perfect fit!!

First, I popped the two clips that hold on the top. Then, I removed two screws and unplugged a few wire connectors to remove the front panel. I scraped off the felt, which was rubbing the drum since the white plastic glides had worn completely through. I applied the high-temp adhesive liberally, laid on the new felt, and applied some spring clamps to hold it in place. I removed the small back panel to replace the belt, which was really easy with the dryer apart. The 7-year-old original belt was a little cracked.

As all others have said, without being redundant, I'd view post #1 or #2 for a good detailed set of instructions.

The primary issue I had was with the stainless steel ball bearing that was shipped with the kit. I couldn't figure out what it was used for, because when I removed the bearing carrier the ball fell out before I could see where the original one was located. The stainless ball bearing is a grounding ball, not a bearing. It goes on the exterior of the plastic bearing carrier/receiver.

Once I figured that part out, it was a piece of cake.

Took a little longer than other people's repairs, but I also put a new belt on and re-worked the exhaust duct for solid ducting versus flexible duct. fine-tuning the rigid duct work was a piece of cake with the tumbler out, since i could crawl right inside the chassis and make sure everything would line up (level legs, adjust elbows, etc)

UNPLUGGED the dryer!!! Search this site they have instructions for many of the tasks they sell parts for... disconnect the vent hose, removed the access panel for the motor & belt (rear) (1/4 nut driver), slipped the belt off the idler pulley and motor pulley, carefully lifted the front edge of the top panel & rotated it back on the hinges, labeled and removed the door interlock wires (2), removed 4 screws securing the top of the front panel (5/16 nut driver) (magnetic is best), removed a yellow guide also attached to the top of the front support (5/16 nut driver), rotated the top of the front panel clear of the drum opening (while supported) and lifted the front panel off the bottom guides, carefully lifted the back of the drum straight up about an inch while supporting the front of the drum, remove the drum from the opening created by removing the front panel (the belt should come out with the drum, removed the rear parts of the new bearing (atteched to teh back of the dryer) 5/16 nut driver... you will need a helper to catch the ball bearing holder on the exterior back of the dryer in the middle, unscrew the drum half of the bearing assembly from inside the drum (3 phillips head screws). I have done this several years ago and you will be amazed at how much dust and lint there is... CLEAN AND VACUUM EVERYWHERE AND THEN ALL THE PLACES YOU MISSED DONT FORGET THE VENT HOSE. Clean all of the old grease from the back of the drum and dryer. Installation is the reverse of removal. Don't forget the new grease and DON"T loose the cute little ball bearing that comes in the new kit. There are lots of sharp metal edges inside so use caution and hopefully you got a new belt since belt replacement requires all of the same steps except for the actual bearing removal.

I can attest to this system only on my model since this is the second bearing I have done.

Sure beats the cost of a new dryer!!! Thanks PARTS SELECT This is the 5th appliance I have repaired for freinds and family with parts purchased from your site.

1.Removed access panel on back of machine in order to place a block under the drum(see step 3).2. Removed the top (clips), 3.removed the front panel(clips), block placed under drum earlier prevents drum from tilting and makes removing front panel with door very easy.4. Slipped new belt on. 5.Replaced front panel and removed block under drum. 6. Aligned belt and checked movement of drum, 7. attched belt to pulley on motor and positioned belt tensioner.8. Installed top and access panels.
This repair is very straight forward, block under drum makes things easy, since the drum stays level when the front panel is removed and replaced.

Took a putty knife and released top clips. Tipped top back , and took out 4 screws holding front cover in place. Lifted out drum, replaced bearing plate. Removed 2 screws and replaced back panel bearing. Placed drum back in place, installed front panel, snapped top back in place and job was done. Very easy. Took about one hour.

Just like in the video, but with a stackable washer/dryer unit, works like new now....

Opened the top of the dryer (no tools needed).
used socket set and removed the two screws (one on each side). unpluged wires from front panel, labled each (good practice).
Pulled open the front panel.
cleaned old felt off all around the front panel. Wiped down everything. while I had it opened, I vaccumed out the dryer underneath.
used glue provided in felt kit and glued new felt where old was.
let dry, put front panel back on ensuring that the felt was between drum and front panel.
put screws back in front panel. closed top.
Let me say that this is the third time I've done this to this dryer as it is about 18 years old.
Until the heating coils go out, this is the cheapest fix there is. :-)