DE3270 Speed Queen Dryer - Instructions

My Dearest One removed the screws that held the part that covers the bulb; removed the old bulb, put in the new bulb and replaced the cover.
The whole operation took less than 5 mins.
Thank you.

The old door catch broke and fell into the unit. Ordered the new part which arrived fast and snapped it into place. Perfect fit and the door now closes/latches correctly - like new again. Would recommend your web site to all do-it-yourselfers. Loved browsing your site, especially seeing all of the schematics and parts list for my unit.

I used a screwdriver to pry out the broken door latch and inserted the new one in the same slot. Perfect fit. The picture of the part in the order page was a big help to identify the correct part.

removed bottom panel.Has 2 screws on bottom.take belt off of idler. take 2 screws out of motor base.turn motor sideways& remove bolt from arm that holds idler. remove snapring holding idler. replace pully & reassemble in reverse. Thank You Partselect for prompt shipping. A+ Rating

Disconnect the dryer from the electrical source. Using a nut driver, first remove the 2 screws of the lower panel and release the panel. Next remove 4 screws of the door panel and then remove the electrical connections to the door (6 wires). Remember to mark the wires prior to removing so you will remember were it plugs back in on reassembly. Remove the door panel. Then remove the 2 screws holding the top of the dryer and tilt the top open about 90 degrees to access the tumbler. Remove the belt by sliding off the tumbler. Remove the tumbler. You will then access the pulley. Using a pair of pliers, remove the retaining ring by pulling upwards. Then remove the washer and the pulley. Replace the parts with the new pulley, washer and retaining ring. This time would be a good time to replace the belt too. Thread the belt through the pulley and over the tumbler. Place the top back and screw in place. Reassemble the door wiring and reattach the door with the 4 screws. Reassemble the lower panel and plug the dryer back into the outlet and test. There should be no more noise if the noise is coming from the pulley and loose belt.

Popped in the new part. Really! That easy!

used one nut driver, basically took the whole machine apart. took snap ring off the idler shaft, replaced pulley, and put it back together. simple job.

clothes drier didn't work, tore the drier apart, found problem went looking for the part locally, didn't find it, got mad, went on line, found Parts Select, ordered part, part under $20.00 delivered, part delivered, put everything back together , can dry clothes again, didn't have to find $350.00 to go buy a new drier. Merry Christmas!

To start the repair, I removed the two front panels. Disconnecting the wiring to door and light. Next removing dryer drum and drive belt[ allows access to belt tensioner] replace tensioner roller, then reassemble. Dryer works fine

I ordered the part. ( I should have ordered just in case it happens again.) When it got here it took less than a minute to snap it in.

Just snapped the new plastic latch into the hole (the hole was there because in trying to extract the old latch, it fell into the inside of the door). Took two seconds. Order to arrival of the part took only 22 hours!

Pulled out the broken part than easily snapped the new part into place..

Push new catch in the opening, close the door and VOILA! the door stays closed. Please note that the cost of this part is exorbitant- it's worth about 50 cents but with shipping it cost about $11.00. Check your local hardware store first.

I would like to say first of all that I was amaized and pleased at how simple the ordering of this part was and while looking at the parts diagram on you website I noticed the door swing was optional and could be easily changed and the dryer came from the factory with a latch installed on both sides of the door. In our laundry room the dryer sits to the left of the washer and the door to the dryer opened to the right which has always been a slight inconvenience. . . So instead of changing out the broken part, I took the door and hinge off with my cordless screwdriver (6-8 screws) and turned it around and remounted it on the opposite side. . . Simple! I never took the new part out of the ups envelope. Now I have a spare so I taped the new part in the envelope to the back of the dryer in case I ever need it and now we have more convenience with the door swinging the correct way. Sweet deal! Took less than an hour. Thank you for making this task simple. Chuck g.

Removed the front of the dryer. Took out the drum. Now everything inside is easy to get to. You do not need to remove the top. Upon inspection we found that we also needed to replace both felts, teflon guides, drive belt, and both support rollers ans shafts. Basically we rebuilt the dryer. It's quiet now and working like new.