All Installation Instructions for General Electric Dryer DBXR463EDC

Purchased a used dryer & lint filter had holes due to rust

On my GE Dryer the lint filter is located inside the door at the bottom. The filter can just be pulled out by hand & a new one pushed into place

Parts Used:

Lint Filter - White Frame

Barry from WARRIOR, AL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

evidently the pulley spring on video was very very very weak

the pulley spring took so much pressure to hold it down it took 3 men and a boy to hold it and place it in position to to get the belt on. Also there is not enough room to get your arms and hands in without getting some small cuts.Ultimately I removed the screws in the back of the dryer and spread the side of the dryer out to gain proper access. It was an easy repair if the spring would not have been so strong.

Parts Used:

Drive Belt

tim from NEW PRT RCHY, FL
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Rubbing noise while dryer was running

Removed too of dryer and placed the parts on. Runs like a brand new one. Thanks so much!

Parts Used:

DRYER BEARING SLIDE GREEN 2PK

Carol from Simpsonville, SC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

not drying clothes, felt seal hanging in the dryer

Took dryer apart replaced felt seal and the four drum slides put it back together works better now than when it was new!!!!!!

Parts Used:

Duct Felt Seal

DRYER BEARING SLIDE GREEN 2PK

DRYER FRONT BEARING WHITE 2PK

Adrian from Rutland, VT
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Dryer was making a loud squealing noise.

I replaced the dryer bearing ( a plastic part) and all of the slides on the bearing. It now operates like new.

Parts Used:

DRYER BEARING SLIDE GREEN 2PK

Patrick from Albuquerque, NM
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

old screen was not sealing properly

Replaced new screen in place of old one.

Parts Used:

Lint Filter - White Frame

Thomas from Wake Forest, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

door filter

was no repair- removed filter from door and installed new filter into door. No tools required.

Parts Used:

Lint Filter - White Frame

victor from ST AUGUSTINE, FL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Bulb

Open dryer door, reach in at the 12 o'clock postion
on the inside is the bulb.

Parts Used:

Light Bulb

Mark from Monroe Township, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burnt out bulb

Used a flash light to see, reached in and installed new bulb above the door

Parts Used:

Light Bulb

Jeffry from ROCKVILLE, MD
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Bulb was intermittently working

Inspected door switch operation and was working properly and simply looked for bulb in the dryer drum housing and located it immediately above the door opening,unscrewed it and noticed the broken elements inside. The bulb is a 10w/120V. Installed bulb problem solved.

Parts Used:

Light Bulb

Peter from LEOMINSTER, MA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Original terminal grounding block melted for unknown reason.

Unscrewed the old, screwed in the new making sure wires matched up same as before. Reset my breaker and works like new again.

Parts Used:

Terminal Block and Grounding Strap

Manuel, J from MCALESTER, OK
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

light bulb dead

remove the old one and put the new one...!!! Easy

Parts Used:

Light Bulb

Carole from Wynnewood, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

I broke the door strike on the dryer.

Wife was out of town, visiting family. I broke the door strike by wedging the dryer door between the laundry room door, closed the laundry room door and it snapped the door strike breaking it. I ordered the part, and it shipped fast using the standard shipping, nothing fancy. Grabbed a pair of pliers and pushed the new door strike into place. It snapped right in, fits and works perfect like nothing ever happened. The wife will never know :)

Parts Used:

Door Strike

CHRISTOPHER from PHENIX CITY, AL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

clothes being eaten first then the loud noise

I replaced front and rear bearing.The rear I replaced because of cause and effect.There was some play so I am glad I replaced the rear too. Make sure you order drum slides. Ken

Parts Used: