This authentic, white Drum Bearing Slide, also known as the bearing drum slide, glide, or pad, is a plastic, easy-to-install part for your dryer. It replaces the dryer's front drum slide to allow for ...
This original equipment manufacturer Drum Bearing Slide is a plastic, green, easy-to-install part for your dryer. It replaces the dryer's front drum slide to allow for easier movement. You'll know if...
The drum slides are not included with this part. The top bearing helps your dryer operate as quietly as possible. This part will require two green drum slides and 2 white drum slides.
TThe door strike for your dryer is mounted on the dryer frame that the door shuts onto. It fits into the door catch on the door and keeps the door closed. If the door strike is damaged or missing, the...
This rear drum bearing kit comes with a shaft, bearing and installation instructions. The bearing plate comes with a slot in it for the ground strap. Helps keep your dryer running as smoothly as poss...
This part is the replacement high-limit thermostat or safety thermostat for your dryer. The high-limit thermostat is found on the upper right-hand side of the heater housing, and it cuts off power to ...
This is a replacement O-ring for the drum bearing retainer on your dryer. The drum bearing is found at the back of the dryer drum. The O-ring is designed to create a seal on the drum bearing. The O-r...
$32.62
Special Order
Questions And Answers for DBVH520EJ2WW
Ask our experts a question about this model and we'll get back to you as soon as possible!
7 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Wayne
January 19, 2020
GE dryer i cannot change the time with the + and buttons. The clean vent light is on, i keep it clean each time it is used. Thanks wayne
For model number DBVH520EJ2WW
Hello, Thank you for your question. You will need to check into: Part #: PS1482261. This is the main control board that operates the unit. We hope this helps, good luck with this repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Brenda
December 22, 2019
How do i repair the paint that is peeling around the back wall of the drum?
For model number DBVH520EJ2WW
Hello Brenda and thank you for writing.
The paint. This part is discontinued for your model and is no longer available. We have no known replacement information in our system. We recommend you contact the manufacturer of the part to see if they have recently released a new substitute. You might be able to pick up a metal paint spray at a local hardware store or home depot, that should do the trick. We hope this helps. Please contact us anytime.
Was this helpful?
Thank you for voting!
Jennifer
July 22, 2022
In the past few months the top of my dryer is peeling.
For model number DBVH520EJ2WW
Hello Jennifer, thank you for your question. We do sell the Top Panel PS1017066 as well as the Front Panel PS1017082. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you.
Dryer starts most of the time, but then stops. Doesn't dry clothes
For model number DBVH520EJ2WW
Hi Susan, thank you for asking. If your dryer starts and stops without drying clothes, you may need to check the moisture sensor, part number PS1021860, to fix the issue. It detects the amount of moisture in the laundry load and signals the control board when to stop. We hope this sorts out your problem!
Hi, my dryer just hums, displays clean lint filter & will not start
For model number DBVH520EJ2WW
Hi Sherry, thank you for reaching out. We would suggest cleaning the lint filter, part number PS1022431, and making sure it is installed properly. If the filter is broken or damaged, you may have to replace it. A clogged lint filter may cause the motor to overheat, resulting in the dryer not starting. We hope this information helps!
It was pretty easy. After already taking apart the dryer to install a new belt I knew exactly my plan of action. I removed the two screws that hold the top panel of the dryer to the front panel. I then removed the top panel and removed the screws that hold the front to each side panel. I than pulled the front away from the cabinet and drum. I put the new slides in place and installed a new felt strip. I put it back together and that was that. Very easy.
1. Removed top cap on lid by removing the 3 - phillips screws. 2. removed front digital display panel from PC board. 3. removed bolts with nut-driver on the top of the front panel, removed bottom screws with #2 square bit. 4. removed "snap-in" plastic top bearing ( paying attention to where wiring is routed within this frame. 5. cleaned all areas of plastic and felt debris, installed new bearing, felt, and glides. 6. Re-installed all wiring and panels.
*** make sure to order all of the glides, there should be a total of 4 for the top assembly.
Removed the front Dryer panel. Left drum in place and lifted it up slightly to get access to motor drive. Slipped belt in place and put panel back on. This was a first attempt ever at fixing an appliance and it was no big deal.